Adjusting the Projection, Angle | Runco LS-HB guide

Installation

Adjusting the Projection ➤	If the screen is significantly higher or lower than the projector, you can also tilt the
Angle	projector at a slight angle. In a ceiling installation, you do this by adjusting the ceiling
	mount.
	For a floor installation, turn the adjustable feet at the bottom of the projector to adjust the
	projection angle.
	The projector can be rotated (side-to-side) up to 360 degrees and mounted without it
	affecting performance. However, to ensure optimal performance of the lamp, limit the
	front-to-back tilt of the projector to ±20 degrees; see Figure 3-7.

± 360º

± 20º

Figure 3-7. Mounting Angle Ranges (Side-to-Side and Front-to-Back)

If you do this, you may need to vertically shift the image to compensate. For detailed instructions, refer to Primary Lens Adjustments on page 38.

28	Runco LS-HB Installation/Operation Manual

Image 44

Runco LS-HB operation manual Adjusting the Projection, Angle

Contents

LS-HB Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of Conformity FCC Part Page Table of Contents Operation Serial Communications Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures List of Figures Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Optional Accessories Controls and Functions LS-HB at a Glance Source Cursor Keys LS-HB Rear/Bottom/Top View Runco Logo Badge LS-HB Rear Panel RGB LS-HB Remote Control Trigger 1 3.5-mm, mini phono jackRS-232 OFF Memory Preset Buttons M1 / M2 / M3 Picture Adjustment Buttons ContrastSharpness Sharp Press to adjust sharpness Gamma Gamma Aspect Ratio Selection Button Controls and Functions Operation InstallationRemote Control IR Reception Angles For Details, Refer Quick SetupStep Procedure Considerations InstallationInstallation Type Estimating Throw Distance Ambient LightThrow Distance Vertical and Horizontal PositionPrimary Lens Screen Lens Only Anamorphic Minimum Maximum Lens Shift Ceiling InstallationFloor Installation Folded Optics Installing the Optional Anamorphic Lens Mount Installing the MovableTransport Assembly Anamorphic Lens Attaching the Transport Assembly Attachment Plate Do not OVER-TIGHTEN the Screws Ceiling Mount Plate Attachment Plate Projector bottom Plate Installation Do not use the mounting screws provided with the ceiling Anamorphic Lens BasePlate Mounting the LS-HB Adjusting the Projection Angle Connector Panel Access Connections to the LS-HB HDMI/DVI Connections See Figure Connecting SourceComponents to the LS-HB RGB Connections Computer RGB Camcorder 10. Scart Rgbs Connection Gaming Console 11. Component Video Connections DTV-Set-Top Box 12. Composite and S-Video Connections Camcorder RS-232 Controller Connection Theater Equipment Connecting 12-VoltTrigger Output to External Connecting an External IR Connecting to AC PowerReceiver Is appropriate to your locale Turning on the Power Primary Lens Adjustments Zoom Out Focus Zoom Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling Mode Installing and Adjusting the Anamorphic Lens It is extremely important that the primary lens is properly Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Tighten the knobs Installation Operation Selecting Video MemorySelecting an Aspect Ratio Selecting An Input Source Using Picture-In-Picture PIP PIP Input Source Using the On-Screen Menus LS-HB Main Menu Aspect Ratio Settings 169 169 Narrow Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-HB Advanced Menu Same frame rate as the main source RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. LS-HB System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Operation Language 15. LS-HB Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp Replacement Troubleshooting Tips Symptom Possible Causes Solution LS-HB Maintenance and Troubleshooting Key Commands Serial Communications Serial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname Set Gam.crt Operations Control Commands Function Action on unit Lit.tog Serial Commands Operation Commands Values Save.isf Resync Execute Color.space = ? Trans.menu = ? Soft.version RS-232 Error Codes Error Code LED Indication Description Fan 1 failed Serial Communications Specifications LS-HB Specifications LS-HB Specifications Dimensions Weight without lensOperating Temperature Universal Power Supply LS-HB Dimensions LS-HB Dimensions Supported Timings ComponentComposite KHz PAL-B/G Page 020-1093-00 Rev. a November