Source Enable Sub-Menu | Runco LS-HB guide

Operation

Source Enable: To enable or disable selection of a source, choose Source Enable from the System menu and press ENTER. This displays the Source Enable sub-menu, shown in Figure 4-12.

Figure 4-12. Source Enable Sub-Menu

•HDMI 1/HDMI 2: Enables or disables the HDMI 1 and HDMI 2 sources.

•RGB: Enables or disables the RGB source.

•Comp 1: Enables or disables the Component 1 source.

•Video: Enables or disables the Composite video source.

If either Component 1 or Video is enabled, SCART must be disabled.

Note

•S-Video:Enables or disables the S-Video source.

•SCART: Enables or disables the SCART RGBS source.

If SCART is enabled, both Component 1 and Video must be disabled.

Note

Runco LS-HB Installation/Operation Manual

63

Image 79

Runco LS-HB operation manual Source Enable Sub-Menu

Contents

LS-HB Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingSerial Communications Table of Contents Xiv List of Figures List of Figures About This Manual Introduction If you need Turn to Using This Manual Description, Features and Benefits Optional Accessories LS-HB at a Glance Controls and Functions Cursor Keys Source LS-HB Rear/Bottom/Top View Runco Logo Badge RGB LS-HB Rear Panel OFF LS-HB Remote ControlTrigger 1 3.5-mm, mini phono jack RS-232 Aspect Ratio Selection Button Memory Preset Buttons M1 / M2 / M3Picture Adjustment Buttons Contrast Sharpness Sharp Press to adjust sharpness Gamma Gamma Controls and Functions Remote Control InstallationOperation IR Reception Angles Step Procedure Quick SetupFor Details, Refer Installation Type InstallationConsiderations Throw Distance Ambient LightEstimating Throw Distance Lens Screen Lens Only Anamorphic Minimum Maximum Vertical and HorizontalPosition Primary Floor Installation Ceiling InstallationLens Shift Folded Optics Anamorphic Lens Installing the Optional Anamorphic Lens MountInstalling the Movable Transport Assembly Attaching the Transport Assembly Attachment Plate Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the Screws Plate Installation Plate Anamorphic Lens BaseDo not use the mounting screws provided with the ceiling Mounting the LS-HB Angle Adjusting the Projection Connections to the LS-HB Connector Panel Access Components to the LS-HB Connecting SourceHDMI/DVI Connections See Figure Computer RGB Camcorder RGB Connections Gaming Console 10. Scart Rgbs Connection DTV-Set-Top Box 11. Component Video Connections Camcorder 12. Composite and S-Video Connections Connection RS-232 Controller Trigger Output to External Connecting 12-VoltTheater Equipment Is appropriate to your locale Connecting an External IRConnecting to AC Power Receiver Zoom Out Focus Zoom Turning on the Power Primary Lens Adjustments Rear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture Orientation It is extremely important that the primary lens is properly Installing and Adjusting the Anamorphic Lens Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Tighten the knobs Installation Selecting An Input Source OperationSelecting Video Memory Selecting an Aspect Ratio PIP Input Source Using Picture-In-Picture PIP Using the On-Screen Menus LS-HB Main Menu 169 Aspect Ratio Settings Narrow 169 Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-HB Advanced Menu Same frame rate as the main source RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. LS-HB System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Operation Language 15. LS-HB Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and Troubleshooting Symptom Possible Causes Solution Troubleshooting Tips LS-HB Maintenance and Troubleshooting Serial Communications Key Commands RS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR Codes Gam.crt Lit.tog Operations Control Commands Function Action on unit Operation Commands Values Serial Commands Save.isf Resync Execute Color.space = ? Trans.menu = ? Soft.version Error Code LED Indication Description RS-232 Error Codes Fan 1 failed Serial Communications LS-HB Specifications Specifications LS-HB Specifications Universal Power Supply DimensionsWeight without lens Operating Temperature LS-HB Dimensions LS-HB Dimensions KHz Supported TimingsComponent Composite PAL-B/G Page 020-1093-00 Rev. a November