Mounting the LS-HB | Runco specs

Installation

There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another.

In typical front and rear screen installations, the projector can be mounted to a secure and level surface such as a table or cart. Carts are useful when moving a projector during a presentation or from site to site. If possible, lock the wheels when it’s in position to prevent it from being moved during a presentation.

3.5

Mounting the LS-HB

Floor Mounting (Upright)

For fixed installations, and for those that want the projector out of sight or have a limited			Ceiling Mounting
space for projector and audience, you can invert the LS-HB and suspend it from the			(Inverted)
ceiling using a specially-designed ceiling mount fixture.
	Note	For ceiling installations, use Runco-approved mounting hardware
		and M4 screws with a maximum screw depth of 10 mm (0.39 inch).
Install the ceiling mount kit according to the instructions provided with it.
If you are ceiling-mounting an LS-HB with a movable anamorphic lens: Perform
these additional steps to secure the plate Security Hooks to the ceiling (refer to Attaching
the Security Hooks on page 25).
1.	Install ceiling hooks (not supplied) into the ceiling directly above the Plate Hooks. The
	ceiling hooks should be small enough to accept a Chain End but strong enough when
	installed to each support 40 pounds or more.
2.	Attach a Chain End to the Chain and then connect it to one of the ceiling hooks.
3.	Cut the Chain to a length equal to or slightly greater than the distance between the
	ceiling hook and the corresponding Plate Hook.
4.	Attach a Chain End to the other end of the Chain. Then, use the Chain to connect the
	ceiling hook and the Plate Hook.
5.	Repeat Steps 2 through 4 for the other ceilling hook/Plate Hook pair.
The projector can also be inverted and placed in an enclosure above and behind the			Installing the Projector in
viewing area. Install four feet on the inside bottom surface of the enclosure on which the			an Enclosure
projector can rest. A variety of materials can be used for this purpose (for example, rubber
crutch tips or turntable feet).

Runco LS-HB Installation/Operation Manual

27

Image 43

Runco operation manual Mounting the LS-HB

Contents

LS-HB Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingSerial Communications Table of Contents Xiv List of Figures List of Figures About This Manual Introduction If you need Turn to Using This Manual Description, Features and Benefits Optional Accessories LS-HB at a Glance Controls and Functions Cursor Keys Source LS-HB Rear/Bottom/Top View Runco Logo Badge RGB LS-HB Rear Panel OFF LS-HB Remote ControlTrigger 1 3.5-mm, mini phono jack RS-232 Aspect Ratio Selection Button Memory Preset Buttons M1 / M2 / M3Picture Adjustment Buttons Contrast Sharpness Sharp Press to adjust sharpness Gamma Gamma Controls and Functions Remote Control InstallationOperation IR Reception Angles Step Procedure Quick SetupFor Details, Refer Installation Type InstallationConsiderations Throw Distance Ambient LightEstimating Throw Distance Lens Screen Lens Only Anamorphic Minimum Maximum Vertical and HorizontalPosition Primary Floor Installation Ceiling InstallationLens Shift Folded Optics Anamorphic Lens Installing the Optional Anamorphic Lens MountInstalling the Movable Transport Assembly Attaching the Transport Assembly Attachment Plate Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the Screws Plate Installation Plate Anamorphic Lens BaseDo not use the mounting screws provided with the ceiling Mounting the LS-HB Angle Adjusting the Projection Connections to the LS-HB Connector Panel Access Components to the LS-HB Connecting SourceHDMI/DVI Connections See Figure Computer RGB Camcorder RGB Connections Gaming Console 10. Scart Rgbs Connection DTV-Set-Top Box 11. Component Video Connections Camcorder 12. Composite and S-Video Connections Connection RS-232 Controller Trigger Output to External Connecting 12-VoltTheater Equipment Is appropriate to your locale Connecting an External IRConnecting to AC Power Receiver Zoom Out Focus Zoom Turning on the Power Primary Lens Adjustments Rear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture Orientation It is extremely important that the primary lens is properly Installing and Adjusting the Anamorphic Lens Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Tighten the knobs Installation Selecting An Input Source OperationSelecting Video Memory Selecting an Aspect Ratio PIP Input Source Using Picture-In-Picture PIP Using the On-Screen Menus LS-HB Main Menu 169 Aspect Ratio Settings Narrow 169 Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-HB Advanced Menu Same frame rate as the main source RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. LS-HB System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Operation Language 15. LS-HB Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and Troubleshooting Symptom Possible Causes Solution Troubleshooting Tips LS-HB Maintenance and Troubleshooting Serial Communications Key Commands RS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR Codes Gam.crt Lit.tog Operations Control Commands Function Action on unit Operation Commands Values Serial Commands Save.isf Resync Execute Color.space = ? Trans.menu = ? Soft.version Error Code LED Indication Description RS-232 Error Codes Fan 1 failed Serial Communications LS-HB Specifications Specifications LS-HB Specifications Universal Power Supply DimensionsWeight without lens Operating Temperature LS-HB Dimensions LS-HB Dimensions KHz Supported TimingsComponent Composite PAL-B/G Page 020-1093-00 Rev. a November