Connections to the LS-HB, Connector Panel Access | Runco manual

Installation

Proceed as follows to connect the LS-HB to your video sources, external controller(s) – if present – and AC power.

When connecting your equipment:

•Use the correct signal cables for each source.

•Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them.

Using a flat-blade screwdriver, loosen the two screws holding the rear compartment cover in place.

Then, remove the rear compartment cover by tilting it upward.

3.6

Connections to the LS-HB

Connector Panel Access

Runco LS-HB Installation/Operation Manual

29

Image 45

Runco operation manual Connections to the LS-HB, Connector Panel Access

Contents

LS-HB Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Maintenance and Troubleshooting SpecificationsSerial Communications Table of Contents Xiv List of Figures List of Figures About This Manual Introduction If you need Turn to Using This Manual Description, Features and Benefits Optional Accessories LS-HB at a Glance Controls and Functions Cursor Keys Source LS-HB Rear/Bottom/Top View Runco Logo Badge RGB LS-HB Rear Panel Trigger 1 3.5-mm, mini phono jack LS-HB Remote ControlRS-232 OFF Picture Adjustment Buttons Contrast Memory Preset Buttons M1 / M2 / M3Sharpness Sharp Press to adjust sharpness Gamma Gamma Aspect Ratio Selection Button Controls and Functions Installation Remote ControlOperation IR Reception Angles Quick Setup Step ProcedureFor Details, Refer Installation Installation TypeConsiderations Ambient Light Throw DistanceEstimating Throw Distance Position Vertical and HorizontalPrimary Lens Screen Lens Only Anamorphic Minimum Maximum Ceiling Installation Floor InstallationLens Shift Folded Optics Installing the Movable Installing the Optional Anamorphic Lens MountTransport Assembly Anamorphic Lens Attaching the Transport Assembly Attachment Plate Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the Screws Plate Installation Anamorphic Lens Base PlateDo not use the mounting screws provided with the ceiling Mounting the LS-HB Angle Adjusting the Projection Connections to the LS-HB Connector Panel Access Connecting Source Components to the LS-HBHDMI/DVI Connections See Figure Computer RGB Camcorder RGB Connections Gaming Console 10. Scart Rgbs Connection DTV-Set-Top Box 11. Component Video Connections Camcorder 12. Composite and S-Video Connections Connection RS-232 Controller Connecting 12-Volt Trigger Output to ExternalTheater Equipment Connecting to AC Power Connecting an External IRReceiver Is appropriate to your locale Zoom Out Focus Zoom Turning on the Power Primary Lens Adjustments Rear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture Orientation It is extremely important that the primary lens is properly Installing and Adjusting the Anamorphic Lens Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Tighten the knobs Installation Selecting Video Memory OperationSelecting an Aspect Ratio Selecting An Input Source PIP Input Source Using Picture-In-Picture PIP Using the On-Screen Menus LS-HB Main Menu 169 Aspect Ratio Settings Narrow 169 Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-HB Advanced Menu Same frame rate as the main source RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. LS-HB System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Operation Language 15. LS-HB Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and Troubleshooting Symptom Possible Causes Solution Troubleshooting Tips LS-HB Maintenance and Troubleshooting Serial Communications Key Commands RS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR Codes Gam.crt Lit.tog Operations Control Commands Function Action on unit Operation Commands Values Serial Commands Save.isf Resync Execute Color.space = ? Trans.menu = ? Soft.version Error Code LED Indication Description RS-232 Error Codes Fan 1 failed Serial Communications LS-HB Specifications Specifications LS-HB Specifications Weight without lens DimensionsOperating Temperature Universal Power Supply LS-HB Dimensions LS-HB Dimensions Component Supported TimingsComposite KHz PAL-B/G Page 020-1093-00 Rev. a November