Anamorphic Lens Base, Plate | Runco LS-HB specification

Installation

Installing the Fixed ➤ To install the base plate on an LS-HB with a fixed anamorphic lens:

	Anamorphic Lens Base	1.	Place the projector upside down on a blanket or other soft surface.
	Plate
		2.	Secure the base plate and Ceiling Mount Plate (if used) to the projector with the four,

			M4 x 0.7 x 14mm screws provided with the anamorphic lens base plate.

1. Do not use the mounting screws provided with the ceiling

Caution	mounting kit. Use only the hardware provided with the
	mounting kit. Use only the hardware provided with the
	anamorphic lens base plate.
	2. DO NOT OVER-TIGHTEN THE SCREWS.
	Ceiling Mount Plate
	(part of Ceiling Mount Kit)

1 Screw, Phillips Pan-Head,

M4 x 0.7 x 14mm (4x)

2Anamorphic Lens Base Plate

Figure 3-6. Projector with Fixed Anamorphic Lens Base Plate - Bottom View

26	Runco LS-HB Installation/Operation Manual

Image 42

Runco LS-HB operation manual Anamorphic Lens Base, Plate, Do not use the mounting screws provided with the ceiling

Contents

LS-HB Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of Conformity FCC Part Page Table of Contents Operation Maintenance and Troubleshooting SpecificationsSerial Communications Table of Contents Xiv List of Figures List of Figures Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Optional Accessories Controls and Functions LS-HB at a Glance Source Cursor Keys LS-HB Rear/Bottom/Top View Runco Logo Badge LS-HB Rear Panel RGB RS-232 LS-HB Remote ControlTrigger 1 3.5-mm, mini phono jack OFF Sharpness Sharp Press to adjust sharpness Gamma Gamma Memory Preset Buttons M1 / M2 / M3Picture Adjustment Buttons Contrast Aspect Ratio Selection Button Controls and Functions Installation Remote ControlOperation IR Reception Angles Quick Setup Step ProcedureFor Details, Refer Installation Installation TypeConsiderations Ambient Light Throw DistanceEstimating Throw Distance Primary Vertical and HorizontalPosition Lens Screen Lens Only Anamorphic Minimum Maximum Ceiling Installation Floor InstallationLens Shift Folded Optics Transport Assembly Installing the Optional Anamorphic Lens MountInstalling the Movable Anamorphic Lens Attaching the Transport Assembly Attachment Plate Do not OVER-TIGHTEN the Screws Ceiling Mount Plate Attachment Plate Projector bottom Plate Installation Anamorphic Lens Base PlateDo not use the mounting screws provided with the ceiling Mounting the LS-HB Adjusting the Projection Angle Connector Panel Access Connections to the LS-HB Connecting Source Components to the LS-HBHDMI/DVI Connections See Figure RGB Connections Computer RGB Camcorder 10. Scart Rgbs Connection Gaming Console 11. Component Video Connections DTV-Set-Top Box 12. Composite and S-Video Connections Camcorder RS-232 Controller Connection Connecting 12-Volt Trigger Output to ExternalTheater Equipment Receiver Connecting an External IRConnecting to AC Power Is appropriate to your locale Turning on the Power Primary Lens Adjustments Zoom Out Focus Zoom Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling Mode Installing and Adjusting the Anamorphic Lens It is extremely important that the primary lens is properly Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Tighten the knobs Installation Selecting an Aspect Ratio OperationSelecting Video Memory Selecting An Input Source Using Picture-In-Picture PIP PIP Input Source Using the On-Screen Menus LS-HB Main Menu Aspect Ratio Settings 169 169 Narrow Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-HB Advanced Menu Same frame rate as the main source RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. LS-HB System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Operation Language 15. LS-HB Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp Replacement Troubleshooting Tips Symptom Possible Causes Solution LS-HB Maintenance and Troubleshooting Key Commands Serial Communications Serial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname Set Gam.crt Operations Control Commands Function Action on unit Lit.tog Serial Commands Operation Commands Values Save.isf Resync Execute Color.space = ? Trans.menu = ? Soft.version RS-232 Error Codes Error Code LED Indication Description Fan 1 failed Serial Communications Specifications LS-HB Specifications LS-HB Specifications Operating Temperature DimensionsWeight without lens Universal Power Supply LS-HB Dimensions LS-HB Dimensions Composite Supported TimingsComponent KHz PAL-B/G Page 020-1093-00 Rev. a November