Operation | Runco LS-HB instruction

Operation

To turn test patterns off, press any key other than or on the remote control unit or built-in keypad.

Altitude: Select Altitude from the Service Menu to control the operation of the projector’s cooling fan.

In most cases, the default setting (Auto) will maintain the correct operating temperature. If the lamp frequently turns off due to overheating, or in certain high-altitude operating environments, you may need to change this setting to High.

70	Runco LS-HB Installation/Operation Manual

Image 86

Runco LS-HB operation manual Operation

Contents

LS-HB Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of Conformity FCC Part Page Table of Contents Operation Serial Communications Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures List of Figures Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Optional Accessories Controls and Functions LS-HB at a Glance Source Cursor Keys LS-HB Rear/Bottom/Top View Runco Logo Badge LS-HB Rear Panel RGB RS-232 LS-HB Remote ControlTrigger 1 3.5-mm, mini phono jack OFF Sharpness Sharp Press to adjust sharpness Gamma Gamma Memory Preset Buttons M1 / M2 / M3Picture Adjustment Buttons Contrast Aspect Ratio Selection Button Controls and Functions Operation InstallationRemote Control IR Reception Angles For Details, Refer Quick SetupStep Procedure Considerations InstallationInstallation Type Estimating Throw Distance Ambient LightThrow Distance Primary Vertical and HorizontalPosition Lens Screen Lens Only Anamorphic Minimum Maximum Lens Shift Ceiling InstallationFloor Installation Folded Optics Transport Assembly Installing the Optional Anamorphic Lens MountInstalling the Movable Anamorphic Lens Attaching the Transport Assembly Attachment Plate Do not OVER-TIGHTEN the Screws Ceiling Mount Plate Attachment Plate Projector bottom Plate Installation Do not use the mounting screws provided with the ceiling Anamorphic Lens BasePlate Mounting the LS-HB Adjusting the Projection Angle Connector Panel Access Connections to the LS-HB HDMI/DVI Connections See Figure Connecting SourceComponents to the LS-HB RGB Connections Computer RGB Camcorder 10. Scart Rgbs Connection Gaming Console 11. Component Video Connections DTV-Set-Top Box 12. Composite and S-Video Connections Camcorder RS-232 Controller Connection Theater Equipment Connecting 12-VoltTrigger Output to External Receiver Connecting an External IRConnecting to AC Power Is appropriate to your locale Turning on the Power Primary Lens Adjustments Zoom Out Focus Zoom Changing the OSD Language Adjusting the Picture Orientation Rear Projection Ceiling Mode Installing and Adjusting the Anamorphic Lens It is extremely important that the primary lens is properly Adjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Tighten the knobs Installation Selecting an Aspect Ratio OperationSelecting Video Memory Selecting An Input Source Using Picture-In-Picture PIP PIP Input Source Using the On-Screen Menus LS-HB Main Menu Aspect Ratio Settings 169 169 Narrow Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-HB Advanced Menu Same frame rate as the main source RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. LS-HB System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Operation Language 15. LS-HB Service Menu OSD menus are not available when in test pattern mode Operation Maintenance and Troubleshooting Lamp Replacement Troubleshooting Tips Symptom Possible Causes Solution LS-HB Maintenance and Troubleshooting Key Commands Serial Communications Serial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname Set Gam.crt Operations Control Commands Function Action on unit Lit.tog Serial Commands Operation Commands Values Save.isf Resync Execute Color.space = ? Trans.menu = ? Soft.version RS-232 Error Codes Error Code LED Indication Description Fan 1 failed Serial Communications Specifications LS-HB Specifications LS-HB Specifications Operating Temperature DimensionsWeight without lens Universal Power Supply LS-HB Dimensions LS-HB Dimensions Composite Supported TimingsComponent KHz PAL-B/G Page 020-1093-00 Rev. a November