Exmark LZ27KC604 manual Recommended Maintenance Schedules

Page 25

Maintenance

Maintenance

Note: Determine the left and right sides of the machine from the normal operating position.

WARNING

While maintenance or adjustments are being made, someone could start the engine. Accidental starting of the engine could seriously injure you or other bystanders.

Remove the key from the ignition switch, engage parking brake, and pull the wire(s) off the spark plug(s) before you do any maintenance. Also push the wire(s) aside so it does not accidentally contact the spark plug(s).

WARNING

The engine can become very hot. Touching a hot engine can cause severe burns.

Allow the engine to cool completely before service or making repairs around the engine area.

Recommended Maintenance Schedule(s)

Maintenance Service

Maintenance Procedure

Interval

 

 

 

 

 

After the first 5 hours

Change the engine oil.

 

 

After the first 100 hours

• Check the wheel hub slotted nut torque specifications.

• Check the wheel lug nuts.

 

 

 

 

After the first 250 hours

Change the hydraulic filter.

 

 

 

• Check the engine oil level.

 

Check the mower blades.

 

• Check the safety interlock system.

Before each use or daily

• Check the rollover protections systems (roll bar) pins.

• Check the seat belt.

 

 

• Check for loose hardware.

 

• Clean the engine cooling system.

 

• Clean the grass build-up from under the deck.

 

 

 

• Check the hydraulic oil level.

 

• Check the tire pressures.

Every 40 hours

Check the condition of the belts.

 

• Grease the height adjustment shaft bearings.

 

• Grease the rear deck struts.

 

 

Every 50 hours

• Service the air cleaner. (May need more often under severe conditions. See the Engine

 

Owner’s Manual for additional information.)

 

 

 

 

 

Every 80 hours

Remove the engine shrouds and clean the cooling fins.

 

 

 

Every 100 hours

Change the engine oil. (May need more often under severe conditions.)

 

 

 

• Lubricate the brake handle pivot.

 

• Lubricate the brake rod bushings.

Every 160 hours

Lubricate the motion control bronze bushings.

 

• Lubricate the seat switch actuator.

 

• Check the spark plugs.

 

 

 

25

Image 25
Contents Lazer Z California Exmark Parts Plus Program Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationUsing the Rollover Protection System Rops Maintenance and Storage Safety and Instructional Decals 633922 643222 643339 98-5954 103-1798 103-3270 103-4474 103-4930 103-5881 103-6319 107-2102 107-2112 109-1214 109-1215 109-3148 109-7949 103-9255 Model Numbers SpecificationsSystems Dimensions Torque Requirements Product OverviewControls OperationOperating Instructions Pre-StartDisengaging the PTO Engaging the PTOStopping the Engine Driving the MachineDriving Forward Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Transporting a Unit TransportingLoading a Unit Operation Recommended Maintenance Schedules MaintenanceService Interval Before each use or daily Check Battery ChargeService Interval Monthly Check Engine Oil LevelCheck Mower Blades Check Safety Interlock SystemService Air Cleaner Check Rollover Protections Systems Roll Bar PinsCheck Seat Belt Check for Loose HardwareCheck Hydraulic Oil Level Change Engine OilCheck Tire Pressures Check Condition Of BeltsLubricate Caster Wheel Hubs Service Interval YearlyLubricate Brake Handle Pivot Lubricate Seat Switch ActuatorLubricate Brake Rod Bushings Lubricate Motion Control Bronze BushingsFuel Tank Mounting Hardware Specifications Wheel Hub Slotted Nut Torque SpecificationChange Fuel Filter Change Hydraulic System FilterCopper-Based Anti-seize Mobil HTS Grease Or Food-Grade Anti-seizeDielectric Grease Deck LevelingPump Drive Belt Tension Mule Drive Belt Tension AdjustmentBelt Guide Adjustment Brake Link AdjustmentBrake Adjustment Deck Belt TensionReverse Indicator Adjustment Electric Clutch AdjustmentMotion Control Linkage Adjustment Motion Control Damper Adjustment Adjust Seat Switch Caster Pivot Bearings Pre-Load AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine Cooling SystemClean Grass Build-Up Under Deck Waste DisposalMaintenance Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Electrical Diagram SchematicsHydraulic Diagram Year Limited Warranty Exmark Turf Equipment Service Record Page See Exmark’s Complete Line of Accessories