Exmark LZ27KC604 manual Change Engine Oil, Check Hydraulic Oil Level, Check Tire Pressures

Page 29

Maintenance

6.Do Not wash or use pressurized air to clean paper element or inner element.

7.Reinstall elements. Position the cover so that the rubber dust ejector is pointing downward and secure with retaining clips.

Change Engine Oil

Service Interval: After the first 5 hours

Every 100 hours/Yearly (whichever comes first) (May need more often under severe conditions.)

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Drain oil while engine is warm from operation.

3.The oil drain hose is located on right hand side of engine. Place pan under machine to catch oil. Remove plug from end of drain hose. Allow oil to drain and replace oil drain plug. Torque plug to 20-24 ft-lb (27-33 N-m).

4.Replace the oil filter every other oil change. Clean around oil filter and unscrew filter to remove. Before reinstalling new filter, apply a thin coating of oil on the surface of the rubber seal. Turn filter clockwise until rubber seal contacts the filter adapter then tighten filter an additional 1/2 to 3/4 turn.

5.Clean around oil fill cap and remove cap. Fill to specified capacity and replace cap.

6.Use oil recommended in engine owner’s manual. Do Not overfill. Start the engine and check for leaks.

Check Hydraulic Oil Level

Service Interval: Every 40 hours

1.Stop engine and wait for all moving parts to stop. Engage parking brake.

2.Clean area around hydraulic reservoir cap and remove cap. Oil level should be to the top of the baffle inside the tank. If not, add oil. Use only Mobil 1 15W-50 synthetic motor oil. Replace hydraulic reservoir cap and tighten until snug. Do Not overtighten.

Note: The baffle is labeled “HOT” and “COLD”. The oil level varies with the temperature of the oil. The “HOT” level shows

the level of oil when it is at 225°F (107°C). The “COLD” level shows the level of the oil when it is at 75°F (24°C). Fill to the appropriate level depending upon the temperature of the oil. For example: If the oil is about 150°F (65°C), fill to halfway between the “HOT” and “COLD” levels. If the oil is at room temperature (about 75°F (24°C)), fill only to the “COLD” level.

Check Tire Pressures

Service Interval: Every 40 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Check tire pressure in drive tires.

3.Inflate drive tires to 13 psi (90 kPa).

4.Semi-pneumatic caster tires do not need to be inflated.

Note: Do Not add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires may cause failures to the hydro drive system, frame, and other components. Foam filling tires will void the warranty.

Check Condition Of Belts

Service Interval: Every 40 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Unhook seat latch and tilt seat up. Lift the rubber flap on front side of the engine to check pump drive belt.

3.Remove left and right belt shields on deck and lift up floor pan to inspect deck drive belt.

4.Check under machine to inspect the mule drive belt. See Mule Drive Belt Tension Adjustment section.

Lubricate Grease Fittings

Note: See chart for service intervals.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lubricate fittings with one to two pumps of NGLI grade #2 multi-purpose gun grease.

Refer to the following chart for fitting locations and lubrication schedule.

29

Image 29
Contents Lazer Z California Exmark Parts Plus Program Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationUsing the Rollover Protection System Rops Maintenance and Storage Safety and Instructional Decals 633922 643222 643339 98-5954 103-1798 103-3270 103-4474 103-4930 103-5881 103-6319 107-2102 107-2112 109-1214 109-1215 109-3148 109-7949 103-9255 Systems SpecificationsModel Numbers Dimensions Torque Requirements Product OverviewControls OperationOperating Instructions Pre-StartDisengaging the PTO Engaging the PTOStopping the Engine Driving the MachineDriving Forward Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Loading a Unit TransportingTransporting a Unit Operation Recommended Maintenance Schedules MaintenanceService Interval Before each use or daily Check Battery ChargeService Interval Monthly Check Engine Oil LevelCheck Mower Blades Check Safety Interlock SystemService Air Cleaner Check Rollover Protections Systems Roll Bar PinsCheck Seat Belt Check for Loose HardwareCheck Hydraulic Oil Level Change Engine OilCheck Tire Pressures Check Condition Of BeltsLubricate Caster Wheel Hubs Service Interval YearlyLubricate Brake Handle Pivot Lubricate Seat Switch ActuatorLubricate Brake Rod Bushings Lubricate Motion Control Bronze BushingsFuel Tank Mounting Hardware Specifications Wheel Hub Slotted Nut Torque SpecificationChange Fuel Filter Change Hydraulic System FilterCopper-Based Anti-seize Mobil HTS Grease Or Food-Grade Anti-seizeDielectric Grease Deck LevelingPump Drive Belt Tension Mule Drive Belt Tension AdjustmentBelt Guide Adjustment Brake Link AdjustmentBrake Adjustment Deck Belt TensionMotion Control Linkage Adjustment Electric Clutch AdjustmentReverse Indicator Adjustment Motion Control Damper Adjustment Adjust Seat Switch Caster Pivot Bearings Pre-Load AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine Cooling SystemClean Grass Build-Up Under Deck Waste DisposalMaintenance Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Electrical Diagram SchematicsHydraulic Diagram Year Limited Warranty Exmark Turf Equipment Service Record Page See Exmark’s Complete Line of Accessories