Exmark LZ27KC604 manual Caster Pivot Bearings Pre-Load Adjustment, Adjust Seat Switch

Page 38

Maintenance

Caster Pivot Bearings

Pre-Load Adjustment

Remove dust cap from caster and tighten nyloc nut until washers are flat and back off 1/4 of a turn to properly set the pre-load on the bearings. If disassembled, make sure the spring disc washers are reinstalled as shown in Figure 23.

Figure 22

1.Motion control bracket

2.Least resistance (softest feel)

3.Medium resistance (medium feel)

4.Most resistance (firmest feel)

5.Torque nyloc nut to 200 in-lb (16.7 ft-lb). Bolt must protrude past end of nyloc nut after torque.

6.Damper

7.Damper must move freely on bolt.

Adjust Seat Switch

1.If necessary, adjust the seat actuator rod length to where the machine will shut off when the operator raises off the seat (with brake disengaged or PTO engaged) but will continue to run with operator in seat (a slight shift in weight should not shut machine off).

Normal adjustment is when length of spring is 2.09 inches (5.3 cm) (with seat up).

Note: To prevent the engine from cutting out when operating over rough ground, the unit is equipped with a time-delayed seat switch. When the operator raises off the seat with either the brake disengaged or the PTO engaged, the engine should stop after 1/2 second has elapsed.

2.To adjust seat switch actuator rod length, loosen lock nut on bottom of the actuator rod (5/16 x 7 inch bolt) and adjust the nuts to move the actuator plate/washer up or down on the rod, then retighten.

Figure 23

1.Spring disc washers

38

Image 38
Contents Lazer Z California Exmark Parts Plus Program Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and Storage Safety and Instructional Decals 633922 643222 643339 98-5954 103-1798 103-3270 103-4474 103-4930 103-5881 103-6319 107-2102 107-2112 109-1214 109-1215 109-3148 109-7949 103-9255 Systems SpecificationsModel Numbers Dimensions Product Overview Torque RequirementsOperation ControlsPre-Start Operating InstructionsStopping the Engine Engaging the PTODisengaging the PTO Driving the MachineAdjusting the Cutting Height Driving ForwardAdjusting the Anti-Scalp Rollers Loading a Unit TransportingTransporting a Unit Operation Maintenance Recommended Maintenance SchedulesService Interval Monthly Check Battery ChargeService Interval Before each use or daily Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesCheck Seat Belt Check Rollover Protections Systems Roll Bar PinsService Air Cleaner Check for Loose HardwareCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Check Condition Of BeltsService Interval Yearly Lubricate Caster Wheel HubsLubricate Brake Rod Bushings Lubricate Seat Switch ActuatorLubricate Brake Handle Pivot Lubricate Motion Control Bronze BushingsChange Fuel Filter Wheel Hub Slotted Nut Torque SpecificationFuel Tank Mounting Hardware Specifications Change Hydraulic System FilterDielectric Grease Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Deck LevelingMule Drive Belt Tension Adjustment Pump Drive Belt TensionBrake Adjustment Brake Link AdjustmentBelt Guide Adjustment Deck Belt TensionMotion Control Linkage Adjustment Electric Clutch AdjustmentReverse Indicator Adjustment Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load Adjustment Adjust Seat SwitchClean Grass Build-Up Under Deck Clean Engine Cooling SystemRemove Engine Shrouds and Clean Cooling Fins Waste DisposalMaintenance Troubleshooting Problem Possible Cause Corrective ActionTroubleshooting Schematics Electrical DiagramHydraulic Diagram Year Limited Warranty Exmark Turf Equipment Service Record Page See Exmark’s Complete Line of Accessories