Exmark LZ27KC604 manual Specifications, Model Numbers, Systems

Page 15

Specifications

Specifications

Model Numbers

Serial Nos: 720,000 and Higher

LZ27KC604

Systems

Engine

Engine Specifications: See your Engine Owner’s Manual

RPM: Full Speed: 3750 ±50 RPM (No Load)

Idle: 1500 RPM

Fuel System

Capacity: 13.5 gal. (51.0 L)

Type of Fuel: Regular unleaded gasoline, 87 octane or higher.

Fuel Filter: In-line 15 Micron Kohler P/N 2405010.

Fuel Shut-Off Valve: 1/4 turn increments (“ON”, “OFF”).

Fuel gauge in left hand fuel tank.

Electrical System

Charging System: Flywheel Alternator

Charging Capacity: 15 amps

Battery Type: BCI Group U1

Battery Voltage: 12 Volt

Polarity: Negative Ground

Fuses: Two 20 amp blade type

Safety Interlock System

PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Operator Controls

Steering and Motion Control:

Note: Motion control levers are adjustable to two heights.

Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

Steering is controlled by varying the position of the levers relative to each other.

Moving motion control levers outward (in slots) locks the drive system in neutral.

PTO Engagement Switch: Engages electric clutch (to drive belt) which engages mower blades.

Parking Brake Lever: Engages parking brake.

Deck Height Adjustment Lever: Sets cutting height to desired position.

Deck Lift Assist Lever: Foot pedal that assists in raising the deck.

Seat

Type: Standard seat with high back, foam padded (internal suspension) and armrests.

Optional seat accessories:

Custom ride suspension system to enhance Standard Seat.

Deluxe suspension seat with high back, low profile foam-in-place cushion (dampened, adjustable spring suspension) and armrests.

Mounting: Hinged to tilt up for access to hydraulic pumps, battery and other components. Held in tilted position with prop rod. Adjustable fore and aft seat track.

Armrests:

Standard seat: foam padded flip-up armrests.

15

Image 15
Contents Lazer Z California Exmark Parts Plus Program Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationUsing the Rollover Protection System Rops Maintenance and Storage Safety and Instructional Decals 633922 643222 643339 98-5954 103-1798 103-3270 103-4474 103-4930 103-5881 103-6319 107-2102 107-2112 109-1214 109-1215 109-3148 109-7949 103-9255 Specifications Model NumbersSystems Dimensions Torque Requirements Product OverviewControls OperationOperating Instructions Pre-StartDriving the Machine Engaging the PTODisengaging the PTO Stopping the EngineDriving Forward Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Transporting Transporting a UnitLoading a Unit Operation Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeService Interval Before each use or daily Service Interval MonthlyCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Check Rollover Protections Systems Roll Bar PinsService Air Cleaner Check Seat BeltCheck Condition Of Belts Change Engine OilCheck Hydraulic Oil Level Check Tire PressuresLubricate Caster Wheel Hubs Service Interval YearlyLubricate Motion Control Bronze Bushings Lubricate Seat Switch ActuatorLubricate Brake Handle Pivot Lubricate Brake Rod BushingsChange Hydraulic System Filter Wheel Hub Slotted Nut Torque SpecificationFuel Tank Mounting Hardware Specifications Change Fuel FilterDeck Leveling Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Dielectric GreasePump Drive Belt Tension Mule Drive Belt Tension AdjustmentDeck Belt Tension Brake Link AdjustmentBelt Guide Adjustment Brake AdjustmentElectric Clutch Adjustment Reverse Indicator AdjustmentMotion Control Linkage Adjustment Motion Control Damper Adjustment Adjust Seat Switch Caster Pivot Bearings Pre-Load AdjustmentWaste Disposal Clean Engine Cooling SystemRemove Engine Shrouds and Clean Cooling Fins Clean Grass Build-Up Under DeckMaintenance Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Electrical Diagram SchematicsHydraulic Diagram Year Limited Warranty Exmark Turf Equipment Service Record Page See Exmark’s Complete Line of Accessories