Exmark LZ27KC604 manual Check Engine Oil Level, Check Battery Charge, Service Interval Monthly

Page 26

Maintenance

Maintenance Service

Maintenance Procedure

Interval

 

 

 

Every 200 hours

• Grease the brake brackets.

 

 

Every 500 hours

• Check the wheel hub slotted nut torque specifications.

• Check the wheel lug nuts.

 

 

 

Monthly

• Check the battery charge.

 

 

 

• Grease front caster pivots.

 

• Grease the deck drive belt idler arm.

Yearly

• Grease the mule drive belt idler arm.

• Grease the pump drive belt idler arm.

 

 

• Lubricate the caster wheel hubs.

 

• Change the hydraulic filter.

 

 

Periodic Maintenance

Check Engine Oil Level

Service Interval: Before each use or daily

1.Stop engine and wait for all moving parts to stop. Make sure unit is on a level surface.

2.Check with engine cold.

3.Clean area around dipstick. Remove dipstick and wipe oil off. Reinsert the dipstick and push it all the way down into the tube. Remove the dipstick and read the oil level.

4.If the oil level is low, wipe off the area around the oil fill cap, remove cap and fill to the “FULL” mark on the dipstick. Use oil as specified in Engine Owner’s Manual. Do Not overfill.

Important: Do Not operate the engine with the oil level below the “LOW” (or “ADD”) mark on the dipstick, or over the “FULL” mark.

Allowing batteries to stand for an extended period of time without recharging them will result in reduced performance and service life. To preserve optimum battery performance and life, recharge batteries in storage when the open circuit voltage drops to 12.4 volts.

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

Important: Make sure the negative battery cables are disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart for recommended charger settings).

Check Battery Charge

Service Interval: Monthly

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

26

Image 26
Contents Lazer Z California Exmark Parts Plus Program Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and Storage Safety and Instructional Decals 633922 643222 643339 98-5954 103-1798 103-3270 103-4474 103-4930 103-5881 103-6319 107-2102 107-2112 109-1214 109-1215 109-3148 109-7949 103-9255 Systems SpecificationsModel Numbers Dimensions Product Overview Torque RequirementsOperation ControlsPre-Start Operating InstructionsStopping the Engine Engaging the PTODisengaging the PTO Driving the MachineAdjusting the Cutting Height Driving ForwardAdjusting the Anti-Scalp Rollers Loading a Unit TransportingTransporting a Unit Operation Maintenance Recommended Maintenance SchedulesService Interval Monthly Check Battery ChargeService Interval Before each use or daily Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesCheck Seat Belt Check Rollover Protections Systems Roll Bar PinsService Air Cleaner Check for Loose HardwareCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Check Condition Of BeltsService Interval Yearly Lubricate Caster Wheel HubsLubricate Brake Rod Bushings Lubricate Seat Switch ActuatorLubricate Brake Handle Pivot Lubricate Motion Control Bronze BushingsChange Fuel Filter Wheel Hub Slotted Nut Torque SpecificationFuel Tank Mounting Hardware Specifications Change Hydraulic System FilterDielectric Grease Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Deck LevelingMule Drive Belt Tension Adjustment Pump Drive Belt TensionBrake Adjustment Brake Link AdjustmentBelt Guide Adjustment Deck Belt TensionMotion Control Linkage Adjustment Electric Clutch AdjustmentReverse Indicator Adjustment Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load Adjustment Adjust Seat SwitchClean Grass Build-Up Under Deck Clean Engine Cooling SystemRemove Engine Shrouds and Clean Cooling Fins Waste DisposalMaintenance Troubleshooting Problem Possible Cause Corrective ActionTroubleshooting Schematics Electrical DiagramHydraulic Diagram Year Limited Warranty Exmark Turf Equipment Service Record Page See Exmark’s Complete Line of Accessories