Exmark LAZER ZTM Lubrication Chart, Service Interval 40 hrs, Service Interval Refer to chart

Page 28

5.1.10Check tire pressures:

Service Interval: 40 hrs.

a)Stop engine and remove key.

b)Inflate all four tires to 13 psi (90 kPa).

5.1.11Check battery electrolyte level:

Service Interval: 40 hrs.

a)Stop engine and remove key.

b)Tilt seat up.

c)Remove vent caps from battery. Fill with water (distilled is recommended) to bottom of vent wells and replace vent caps.

d)See Assembly Section 3.8, for servicing a new battery.

PART NO. 513747

LOCATION: Top Center of Console

 

Under Front of Seat

5.1.12Check condition of belts:

Service Interval: 40 hrs.

a)Stop engine and remove key.

b)Check under engine deck to check pump drive belt.

c)Remove left and right belt shields on deck and lift up floor pan to inspect deck drive belt.

d)See Sections 5.2.3 and 5.2.4, for belt adjustment.

5.1.13Lubricate grease fittings:

Service Interval: Refer to chart.

a)Stop engine and remove key.

b)Lubricate fittings with one to two pumps of SAE No. 2 multi-purpose gun grease.

Refer to the following chart for fitting locations and lubrication schedule.

LUBRICATION CHART

 

FITTING

INITIAL

NO. of

SERVICE

 

LOCATIONS

PUMPS

PLACES

INTERVAL

1.

Front Casters

2

2

40 hours

2.

Front Caster Pivots

0

2

∗∗ yearly

3.

Height Adj. Shaft Brngs.

1

5

40 hours

4.

Deck Drive Belt Idler Arm

1

1

40 hours

5.

Brake Brackets

1

2

200 hours

6.

Pump Drive Belt Idler Arm

1

1

40 hours

7.

Deck Rear Struts

1

2

40 hours

More often if operating under severe conditions.

∗∗See 5.1.13 Section c) for special lubrication instructions.

- 23 -

Image 28
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingPotential Hazard Operation Maintenance and Storage Potential Hazard Safety Signs Park Brake Specifications Model NumberEngine Fuel SystemOperator Controls Hydrostatic Ground Drive SystemDimensions Tires and WheelsCutting Deck Discharge chute up Discharge chute downAssembly Instructions Service Engine Position Discharge ChuteCharging the battery may produce explosive gasses Operation Instructions Service Hydraulic OILControls Push the lever forward and down to disengage the brake PRE-START Mowing TransportingDo not drive a unit on a public street or roadway Maintenance & Adjustments Periodic MaintenanceService Interval Daily Service Interval Daily or more often in dry conditionsBlade Bolt Installation Service Interval 25 hrs More often under severe conditions Service Interval 100 hrs Service Interval 40 hrService Interval 40 hrs Lubrication ChartService Interval Refer to chart Service Interval 160 hrs Service Interval 80 hrsService Interval As Required Service Interval After First 250 hrs Then yearly thereafterAdjustments Cutting Height PositionANTI-SCALP Roller Adjustment Self-tensioning No adjustment necessary Brake AdjustmentNo adjustment necessary Motion control linkage adjustment Motion Control Adjustment Waste Disposal Mercury Switch DisposalMotor OIL Disposal Trouble Shooting Battery DisposalMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyEngine Troubleshooting Table ProblemElectrical Diagram Hydraulic Diagram Warranty Page Page Page Service Record Page See EXMARK’S Complete Line of Products for Turf Care

LAZER ZTM specifications

The Exmark Lazer ZTM represents a pinnacle of engineering excellence in the world of commercial zero-turn mowers. Renowned for its exceptional performance and durability, it is a favorite among landscaping professionals who require reliable equipment that can tackle the toughest mowing conditions.

At the heart of the Lazer ZTM is the powerful Kohler and Kawasaki engines that provide a range of horsepower options, ensuring that there is a configuration suitable for various mowing tasks. The efficiency of these engines is complemented by advanced cooling systems and heavy-duty air filtration, which helps to extend their life and optimize performance.

One of the standout features of the Lazer ZTM is its innovative UltraCut mowing deck. Available in various cutting widths, from 48 inches to 72 inches, the UltraCut deck is designed to deliver a premium cut quality across a range of grass types and conditions. Its unique design allows for superior airflow, resulting in better clipping dispersal and a clean cut. The adjustable cutting height provides operators with versatility, enabling them to tailor the height to specific requirements.

The Lazer ZTM is equipped with Exmark's innovative RED Technology, which stands for redesigned engine diagnostics. This smart technology allows operators to monitor the mower's performance in real time, providing crucial data on engine health, RPM, and fuel efficiency. This integration of technology enhances operational efficiency, limits downtime, and extends the lifespan of the mower.

Another hallmark of the Lazer ZTM is its robust construction. The frame is engineered from heavy-duty steel, ensuring longevity and resistance to wear and tear. Its commercial-grade components are designed to withstand the rigors of daily use, making it a reliable choice for professional landscapers.

Comfort and ergonomics also play a significant role in the Lazer ZTM’s design. The operator platform features a cushioned seat with adjustable armrests, providing comfort during extended mowing sessions. The control layout is intuitive, allowing for seamless operation and maneuverability in tight spaces.

Overall, the Exmark Lazer ZTM stands out for its combination of power, cutting efficiency, and operator comfort. Its commitment to innovation and quality makes it a leading choice for those looking to elevate their mowing experience. Whether for commercial landscaping or large property maintenance, the Lazer ZTM promises to deliver outstanding results.