Exmark LAZER ZTM manual Motion Control Adjustment

Page 36

TURN BOLT

REVERSE

INDICATOR

HERE

 

END OF

SLOT

LOOSEN

HERE

YOKE

 

TURN HERE

LOOSEN HERE

 

TO ADJUST

LOOSEN HERE

(RIGHTHAND THREAD)

 

(LEFTHAND THREAD)

 

 

FIG. 10

MOTION CONTROL ADJUSTMENT

f)Start engine. Brake must be engaged and motion control levers out to start engine. Operator does not have to be in the seat because of the jumper wire being used.

Run engine at full throttle and release brake.

g)The reverse indicator spring must be correct before the following adjustments can be made. See Section 5.2.10.

h)Begin on either the left or right side of unit and bring the motion control lever into the neutral position.

Adjust pump control rod length by rotating the double nuts on the rod in the appropriate direction until the wheels slightly creep in reverse. (See Fig 10). Move the motion control lever to the reverse position and while applying slight pressure to the lever, allow the reverse indicator spring to bring the levers back to neutral.

The wheel must stop turning or slightly creep in reverse.

NOTE: The motion control lever needs to be in neutral while making any necessary adjustments.

The left rod assembly controls the left wheel and the right rod assembly controls the right wheel.

i)Repeat on opposite side of unit. Tighten locknuts against balljoints.

j)Shut off unit. Remove jumper wire from wire harness connector and plug connector into seat switch.

5.2.12 Caster pivot bearings pre-load adjustment.

a) Remove dust cap from caster and tighten nyloc nut until washers are flat and back off 1/4 of a turn to properly set the pre-load on the bearings. If disassembled make sure the spring washers are reinstalled as shown in Figure 11.

FIG. 11

CASTER ADJUSTMENT

- 31 -

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingPotential Hazard Operation Maintenance and Storage Potential Hazard Safety Signs Park Brake Specifications Model NumberEngine Fuel SystemOperator Controls Hydrostatic Ground Drive SystemDimensions Tires and WheelsCutting Deck Discharge chute up Discharge chute downAssembly Instructions Service Engine Position Discharge ChuteCharging the battery may produce explosive gasses Service Hydraulic OIL Operation InstructionsControls Push the lever forward and down to disengage the brake PRE-START Mowing TransportingDo not drive a unit on a public street or roadway Maintenance & Adjustments Periodic MaintenanceService Interval Daily Service Interval Daily or more often in dry conditionsBlade Bolt Installation Service Interval 25 hrs More often under severe conditions Service Interval 100 hrs Service Interval 40 hrLubrication Chart Service Interval 40 hrsService Interval Refer to chart Service Interval 160 hrs Service Interval 80 hrsService Interval As Required Service Interval After First 250 hrs Then yearly thereafterAdjustments Cutting Height PositionANTI-SCALP Roller Adjustment Self-tensioning No adjustment necessary Brake AdjustmentNo adjustment necessary Motion control linkage adjustment Motion Control Adjustment Mercury Switch Disposal Waste DisposalMotor OIL Disposal Trouble Shooting Battery DisposalMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyEngine Troubleshooting Table ProblemElectrical Diagram Hydraulic Diagram Warranty Page Page Page Service Record Page See EXMARK’S Complete Line of Products for Turf Care

LAZER ZTM specifications

The Exmark Lazer ZTM represents a pinnacle of engineering excellence in the world of commercial zero-turn mowers. Renowned for its exceptional performance and durability, it is a favorite among landscaping professionals who require reliable equipment that can tackle the toughest mowing conditions.

At the heart of the Lazer ZTM is the powerful Kohler and Kawasaki engines that provide a range of horsepower options, ensuring that there is a configuration suitable for various mowing tasks. The efficiency of these engines is complemented by advanced cooling systems and heavy-duty air filtration, which helps to extend their life and optimize performance.

One of the standout features of the Lazer ZTM is its innovative UltraCut mowing deck. Available in various cutting widths, from 48 inches to 72 inches, the UltraCut deck is designed to deliver a premium cut quality across a range of grass types and conditions. Its unique design allows for superior airflow, resulting in better clipping dispersal and a clean cut. The adjustable cutting height provides operators with versatility, enabling them to tailor the height to specific requirements.

The Lazer ZTM is equipped with Exmark's innovative RED Technology, which stands for redesigned engine diagnostics. This smart technology allows operators to monitor the mower's performance in real time, providing crucial data on engine health, RPM, and fuel efficiency. This integration of technology enhances operational efficiency, limits downtime, and extends the lifespan of the mower.

Another hallmark of the Lazer ZTM is its robust construction. The frame is engineered from heavy-duty steel, ensuring longevity and resistance to wear and tear. Its commercial-grade components are designed to withstand the rigors of daily use, making it a reliable choice for professional landscapers.

Comfort and ergonomics also play a significant role in the Lazer ZTM’s design. The operator platform features a cushioned seat with adjustable armrests, providing comfort during extended mowing sessions. The control layout is intuitive, allowing for seamless operation and maneuverability in tight spaces.

Overall, the Exmark Lazer ZTM stands out for its combination of power, cutting efficiency, and operator comfort. Its commitment to innovation and quality makes it a leading choice for those looking to elevate their mowing experience. Whether for commercial landscaping or large property maintenance, the Lazer ZTM promises to deliver outstanding results.
Top Page Image Contents