Exmark LAZER ZTM manual Service Interval 25 hrs More often under severe conditions

Page 26

5.1.5Check safety interlock system.

Service Interval: Daily

a)Check starting circuit. Starter should crank with operator in seat, parking brake engaged, cutting blades disengaged and motion control levers moved out in the neutral lock position.

Try to start with operator out of seat, parking brake engaged, blades disengaged and motion control levers in neutral lock position - starter must not crank.

Try to start with operator in seat, parking brake disengaged, blades disengaged and motion control levers in the neutral lock position - starter must not crank.

Try to start with operator in seat, parking brake engaged, blades engaged and motion control levers in the neutral lock position - starter must not crank.

Try to start with operator in seat, parking brake engaged, blades disengaged, and the left motion control lever in, starter must not crank, repeat again with the right lever in, then with both levers in - starter must not crank.

b)Check kill circuits. Run engine at one-third throttle, disengage parking brake and raise off of seat (but do not get off of machine) engine must stop after approx. 1/2 second has elapsed (seat has time delay kill switch to prevent cut-outs on rough terrain).

Run engine at one-third throttle, engage cutting blades and raise off of seat (but do not get off of machine) engine must stop after 1/2 second has elapsed.

Run engine at one-third throttle, with brake disengaged, move levers in and raise off seat (but do not get off of machine) engine must stop after 1/2 second has elapsed.

Again, run engine at one-third throttle, brake engaged, and move left motion control lever in - engine must stop.

Repeat again moving the right lever in, then moving both levers in - engine must stop whether operator is on seat or not.

NOTE: If machine does not pass any of these tests, do not operate. Contact your authorized EXMARK SERVICE DEALER.

IMPORTANT: It is essential that operator safety mechanisms be connected and in proper operating condition prior to use for mowing.

5.1.6Check for loose hardware.

Service Interval: Daily

a)Stop engine and remove key.

b)Visually inspect machine for any loose hardware or any other possible problem. Tighten hardware or correct the problem before operating.

5.1.7Service air cleaner.

Service Interval: 25 hrs.

more often under severe conditions.

a)Stop engine and remove key.

b)Remove air cleaner compartment cover.

- 21 -

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingPotential Hazard Operation Maintenance and Storage Potential Hazard Safety Signs Park Brake Engine SpecificationsModel Number Fuel SystemOperator Controls Hydrostatic Ground Drive SystemCutting Deck DimensionsTires and Wheels Discharge chute up Discharge chute downAssembly Instructions Service Engine Position Discharge ChuteCharging the battery may produce explosive gasses Controls Service Hydraulic OILOperation Instructions Push the lever forward and down to disengage the brake PRE-START Mowing TransportingDo not drive a unit on a public street or roadway Service Interval Daily Maintenance & AdjustmentsPeriodic Maintenance Service Interval Daily or more often in dry conditionsBlade Bolt Installation Service Interval 25 hrs More often under severe conditions Service Interval 100 hrs Service Interval 40 hrService Interval Refer to chart Lubrication ChartService Interval 40 hrs Service Interval 160 hrs Service Interval 80 hrsService Interval As Required Service Interval After First 250 hrs Then yearly thereafterAdjustments Cutting Height PositionANTI-SCALP Roller Adjustment Self-tensioning No adjustment necessary Brake AdjustmentNo adjustment necessary Motion control linkage adjustment Motion Control Adjustment Motor OIL Disposal Mercury Switch DisposalWaste Disposal Mower Pulls Left or Right W/LEVERS Fully Forward Trouble ShootingBattery Disposal Mower Cuts UnevenlyEngine Troubleshooting Table ProblemElectrical Diagram Hydraulic Diagram Warranty Page Page Page Service Record Page See EXMARK’S Complete Line of Products for Turf Care

LAZER ZTM specifications

The Exmark Lazer ZTM represents a pinnacle of engineering excellence in the world of commercial zero-turn mowers. Renowned for its exceptional performance and durability, it is a favorite among landscaping professionals who require reliable equipment that can tackle the toughest mowing conditions.

At the heart of the Lazer ZTM is the powerful Kohler and Kawasaki engines that provide a range of horsepower options, ensuring that there is a configuration suitable for various mowing tasks. The efficiency of these engines is complemented by advanced cooling systems and heavy-duty air filtration, which helps to extend their life and optimize performance.

One of the standout features of the Lazer ZTM is its innovative UltraCut mowing deck. Available in various cutting widths, from 48 inches to 72 inches, the UltraCut deck is designed to deliver a premium cut quality across a range of grass types and conditions. Its unique design allows for superior airflow, resulting in better clipping dispersal and a clean cut. The adjustable cutting height provides operators with versatility, enabling them to tailor the height to specific requirements.

The Lazer ZTM is equipped with Exmark's innovative RED Technology, which stands for redesigned engine diagnostics. This smart technology allows operators to monitor the mower's performance in real time, providing crucial data on engine health, RPM, and fuel efficiency. This integration of technology enhances operational efficiency, limits downtime, and extends the lifespan of the mower.

Another hallmark of the Lazer ZTM is its robust construction. The frame is engineered from heavy-duty steel, ensuring longevity and resistance to wear and tear. Its commercial-grade components are designed to withstand the rigors of daily use, making it a reliable choice for professional landscapers.

Comfort and ergonomics also play a significant role in the Lazer ZTM’s design. The operator platform features a cushioned seat with adjustable armrests, providing comfort during extended mowing sessions. The control layout is intuitive, allowing for seamless operation and maneuverability in tight spaces.

Overall, the Exmark Lazer ZTM stands out for its combination of power, cutting efficiency, and operator comfort. Its commitment to innovation and quality makes it a leading choice for those looking to elevate their mowing experience. Whether for commercial landscaping or large property maintenance, the Lazer ZTM promises to deliver outstanding results.
Top Page Image Contents