Exmark LAZER ZTM manual Motion control linkage adjustment

Page 35

5.2.11Motion control linkage adjustment.

WARNING

POTENTIAL HAZARD

♦Engine must be running and drive wheels must be turning so motion control adjustment can be performed.

WHAT CAN HAPPEN

♦Contact with moving parts or hot surfaces may cause personal injury.

HOW TO AVOID THE HAZARD

♦Keep fingers, hands, and clothing clear of rotating components and hot surfaces.

CAUTION

POTENTIAL HAZARD

♦Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous.

WHAT CAN HAPPEN

♦The mechanical or hydraulic jacks may not be enough support or may misfunction allowing the unit to fall, which could cause injury.

HOW TO AVOID THE HAZARD

♦DO NOT rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

a)This adjustment must be made with the drive wheels turning. First raise the frame and block up so that drive wheels can rotate freely.

b)Remove the electrical connection from the seat safety switch, located directly to the left of the seat switch assembly beside the hydraulic oil reservoir.

Temporarily install a jumper wire across the terminals in the connector of the wiring harness.

c)Run the unit at least 5 minutes with the drive levers at full forward speed to bring hydraulic system oil up to operating temperature.

d)Tilt seat forward.

e)Loosen locknuts from the ball joints on the two rods which connect the motion control assemblies to the pump control arms (See Fig 10).

NOTE: The nuts to the rear of the unit on each rod have left-hand threads.

- 30 -

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Table of Contents Training SafetyYour Safety is Involved Safety Alert SymbolPotential Hazard Operation Maintenance and Storage Potential Hazard Safety Signs Park Brake Fuel System SpecificationsModel Number EngineHydrostatic Ground Drive System Operator ControlsDischarge chute up Discharge chute down DimensionsTires and Wheels Cutting DeckAssembly Instructions Position Discharge Chute Service EngineCharging the battery may produce explosive gasses Controls Service Hydraulic OILOperation Instructions Push the lever forward and down to disengage the brake PRE-START Transporting MowingDo not drive a unit on a public street or roadway Service Interval Daily or more often in dry conditions Maintenance & AdjustmentsPeriodic Maintenance Service Interval DailyBlade Bolt Installation Service Interval 25 hrs More often under severe conditions Service Interval 40 hr Service Interval 100 hrsService Interval Refer to chart Lubrication ChartService Interval 40 hrs Service Interval 80 hrs Service Interval 160 hrsService Interval After First 250 hrs Then yearly thereafter Service Interval As RequiredCutting Height Position AdjustmentsANTI-SCALP Roller Adjustment Brake Adjustment Self-tensioning No adjustment necessaryNo adjustment necessary Motion control linkage adjustment Motion Control Adjustment Motor OIL Disposal Mercury Switch DisposalWaste Disposal Mower Cuts Unevenly Trouble ShootingBattery Disposal Mower Pulls Left or Right W/LEVERS Fully ForwardProblem Engine Troubleshooting TableElectrical Diagram Hydraulic Diagram Warranty Page Page Page Service Record Page See EXMARK’S Complete Line of Products for Turf Care

LAZER ZTM specifications

The Exmark Lazer ZTM represents a pinnacle of engineering excellence in the world of commercial zero-turn mowers. Renowned for its exceptional performance and durability, it is a favorite among landscaping professionals who require reliable equipment that can tackle the toughest mowing conditions.

At the heart of the Lazer ZTM is the powerful Kohler and Kawasaki engines that provide a range of horsepower options, ensuring that there is a configuration suitable for various mowing tasks. The efficiency of these engines is complemented by advanced cooling systems and heavy-duty air filtration, which helps to extend their life and optimize performance.

One of the standout features of the Lazer ZTM is its innovative UltraCut mowing deck. Available in various cutting widths, from 48 inches to 72 inches, the UltraCut deck is designed to deliver a premium cut quality across a range of grass types and conditions. Its unique design allows for superior airflow, resulting in better clipping dispersal and a clean cut. The adjustable cutting height provides operators with versatility, enabling them to tailor the height to specific requirements.

The Lazer ZTM is equipped with Exmark's innovative RED Technology, which stands for redesigned engine diagnostics. This smart technology allows operators to monitor the mower's performance in real time, providing crucial data on engine health, RPM, and fuel efficiency. This integration of technology enhances operational efficiency, limits downtime, and extends the lifespan of the mower.

Another hallmark of the Lazer ZTM is its robust construction. The frame is engineered from heavy-duty steel, ensuring longevity and resistance to wear and tear. Its commercial-grade components are designed to withstand the rigors of daily use, making it a reliable choice for professional landscapers.

Comfort and ergonomics also play a significant role in the Lazer ZTM’s design. The operator platform features a cushioned seat with adjustable armrests, providing comfort during extended mowing sessions. The control layout is intuitive, allowing for seamless operation and maneuverability in tight spaces.

Overall, the Exmark Lazer ZTM stands out for its combination of power, cutting efficiency, and operator comfort. Its commitment to innovation and quality makes it a leading choice for those looking to elevate their mowing experience. Whether for commercial landscaping or large property maintenance, the Lazer ZTM promises to deliver outstanding results.
Top Page Image Contents