Exmark Lazer Z XP manual Waste Disposal, Motor OIL Disposal, Engine Coolant Disposal

Page 49

6. WASTE DISPOSAL

6.1 MOTOR OIL DISPOSAL

Engine oil and hydraulic oil are both pollutants to the environment. Dispose of used oil at a certified recycling center or according to your state and local regulations.

6.2 ENGINE COOLANT DISPOSAL

CAUTION

POTENTIAL HAZARD

Engine coolant is toxic.

WHAT CAN HAPPEN

Swallowing coolant can cause poisoning.

HOW TO AVOID THE HAZARD

Do not swallow

Keep out of reach of children and pets.

Engine coolant is a 50/50 mixture of Dex-Cool© (ethylene glycol (anti-freeze) with addititives) and water. Ethylene glycol is a pollutant. Dispose of used engine coolant according to your state and local regulations.

6.3 MERCURY SWITCH DISPOSAL

CAUTION

POTENTIAL HAZARD

The mercury contained in the tilt switch is poisonous.

WHAT CAN HAPPEN

Exposure to mercury can cause severe illness.

HOW TO AVOID THE HAZARD

Never attempt to open or repair the tilt switch

Avoid contact with the mercury.

The tilt switch (PN 1-633782) on this unit contains mercury, a hazardous material. Mercury that is outside a sealed container vaporizes at room temperature. The vapors are harmful. Mercury can be absorbed through the skin. Do not attempt to open or repair this switch.

A very small amount of mercury is contained in a hermetically sealed body. The steel switch is then potted in a hard epoxy in a plastic case. It is unlikely that the mercury will ever escape from the enclosure. These high performance and reliable switches are recyclable. Mercury is an important and beneficial compound but requires special care in handling and disposal. When used and managed properly, mercury is not a threat to people or the environment. This information is presented to users so that they are aware that these switches contain mercury and will apply sound disposal practices when these devices reach their normal end of life or are damaged.

Several states have passed laws concerning the disposal of devices containing mercury. In all the remaining states it is advisable to follow similar procedures. The laws state that these sealed devices contain mercury and should not be placed in the garbage until the mercury is removed and reused, recycled or otherwise managed to insure that it does not become part of solid waste or waters. Management and disposal practices must be within relevant federal, state or local laws.

Return the switch to your Exmark dealer if it is faulty and is being replaced or if the unit containing the switch is no longer operating and is being scrapped. If the switch is damaged or broken open use extreme caution in handling. Call your local waste management authority or Exmark Customer Service for instructions.

- 44 -

Image 49
Contents For Serial Nos 510,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Your Safety is Involved SafetySafety Alert Symbol TrainingCarbon monoxide can kill you Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage Engine coolant is toxic Do not Operate Without Guard Safety SignsLocation LH Side of Cutting Page Specifications Tires and Wheels Hydrostatic Ground Drive SystemCutting Deck Torque Requirements DimensionsUncrate Mower Install Rollover Protection System Roll BAR Assembly InstructionsLower Roll BAR Installation Service Battery Install Drive WheelsUpper Roll BAR Installation Machine is shipped with a filled lead acid batteryTilt seat up to gain access to the battery Service Engine Service Engine Coolant Install Motion Control LeversPosition Discharge Chute Control ARM ShaftOperation Instructions Service Hydraulic OILControls Motion Control Positions Push the lever forward and down to disengage the brake Page Mowing PRE-STARTTransporting Do not drive a unit on a public street or roadway Periodic Maintenance Maintenance & AdjustmentsService Interval Daily Service Interval Monthly Service Interval Daily or more often in dry conditions Blade Bolt Installation Canister type, 2 stage cleaner Engine coolant is toxic Coolant Plug Location Service Interval 40 hrs Service Interval 40 hrService Interval Refer to chart Service Interval Once Yearly Lubrication ChartCaster Wheel Assembly Service Interval When Water in Fuel warning light is on Service Interval 160 hrsService Interval As required Service Interval 800 hrsService Interval After First 250 hrs Then yearly thereafter Service Interval 500 hrsAdjustments Cutting Height Position ANTI-SCALP Roller AdjustmentSpring Compression Adjustment Swivel AdjustmentSelf-tensioning idlers, adjust as follows Self-tensioning No adjustment necessaryMule Drive Belts Adjustment Belt Guide Positioning Brake AdjustmentThrottle Tension Reverse Indicator AdjustmentMotion control linkage adjustment Caster Adjustment Motion Control AdjustmentWaste Disposal Mercury Switch DisposalMotor OIL Disposal Engine Coolant DisposalBattery Disposal Trouble ShootingMower Pulls Left or Right W/LEVERS Fully Forward Mower Cuts UnevenlyProblem Troubleshooting TableEngine Warning Systems Page Electrical Diagram Hydraulic Diagram Year Limited Warranty Page Page Service Record Page See EXMARK’S Complete Line of Accessories