Exmark Series X manual 109-8483

Page 13

Safety

		109-8483
1.	Throttle–fast	3.	Choke–on
2.	Throttle–slow	4.	Choke–off

109-9361

Deck Drive Belt Routing

116-0090

116-0157

1. See Operator’s manual

116-0165

For Style B Slotted Nuts — See “Wheel Hub – Slotted Nut Torque Specification” in the Maintenance section

116-0205

116-0211

13

Image 13

Contents Lazer Z Advantage Series X Models California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0752 Model Numbers SpecificationsSystems Hydrostatic Ground Drive System SeatTires & Wheels Cutting DeckOverall Width DimensionsOverall Length Overall HeightAccessory Weight Table Worksheet Curb WeightTread Width Center to Center of Tires, Widthwise Wheel Base Center of Caster Tire to Center of Drive TireTorque Requirements Product OverviewControls OperationFuel Shut-Off Valve Ignition SwitchHour Meter Fuel GaugeLow Voltage Indicator PTO Engagement SwitchDrive Wheel Release Valves Do Not tow machineOperating Instructions Pre-StartDeck Lift Pedal Transport LockStarting the Engine Open the Fuel Shut-Off ValveDisengaging the PTO Engaging the PTOStopping the Engine Driving the MachineDriving Forward Adjusting the Cutting HeightDriving in Reverse Transporting Adjusting the Anti-Scalp RollersTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeProposition 65 Warning Do Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Rollover Protections Systems Roll Bar Knobs Check Safety Interlock SystemCheck Seat Belt Service Air CleanerCheck for Loose Hardware Change Engine OilCheck Condition Of Belts Check Tire PressuresLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Lubricate Brake Handle PivotCheck Spark Plugs Change Fuel FilterChange Hydraulic System Filter and Fluid Wheel Hub Slotted Nut Torque SpecificationStyle a black finish Change Engine Coolant Kawasaki Liquid-Cooled Only Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyStyle B yellow zinc Thread Locking Adhesives Check Spark Arrester if equippedDielectric Grease Copper-Based Anti-seizeDeck Leveling Adjuster screw Yoke 4 inches 8.3 cm Pump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Start the mower while in the operator position Removing the Shim Electric Clutch AdjustmentMotion Control Linkage Adjustment Motion Control Neutral Lock Pivot Adjustment Motion Control Damper AdjustmentMotion Control Handle Adjustment Adjusting the heightAdjusting the Tilt Caster Pivot Bearings Pre-Load AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Fins Clean Debris From MachineWaste Disposal Battery DisposalMotor Oil Disposal Problem Possible Cause Corrective Action TroubleshootingRefer to Check Engine Coolant Level Troubleshooting Electrical Diagram Air-Cooled SchematicsTAN Electrical Diagram Liquid-CooledElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options