Exmark Series X manual Check Tire Pressures, Check Condition Of Belts, Lubricate Grease Fittings

Page 35

Maintenance

Figure 24

1. Full

2. Add

Note: The oil level on the dipstick will be incorrect if the oil is checked when the unit is hot.

7.If the dipstick oil level is at the “add” mark add Exmark Premium Hydro oil.

8.Replace hydraulic reservoir cap and tighten until snug. Do Not overtighten.

Check Tire Pressures

Service Interval: Every 50 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Check tire pressure in drive tires.

3.Inflate drive tires to 13 psi (90 kPa).

4.Semi-pneumatic caster tires Do Not need to be inflated.

Note: Do Not add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires may cause failures to the hydro drive system, frame, and other components. Foam filling tires will void the warranty.

Check Condition Of Belts

Service Interval: Every 50 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Remove left and right belt shields on deck and lift up floor pan to inspect deck drive belt.

3.Check under machine to inspect the pump drive belt.

Note: No adjustments are required for belt tension.

Lubricate Grease Fittings

Note: See chart for service intervals.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lubricate fittings with one to two pumps of NGLI grade #2 multi-purpose gun grease.

Refer to the following chart for fitting locations and lubrication schedule.

Lubrication Chart

Fitting	Initial	Number of	Service
Locations	Pumps	Places	Interval
1. Deck and	1	2	Yearly
Pump Idler
Pivots
2. Front	*0	2	*Yearly
Caster
Pivots

*See step 3 for special lubrication instructions on the front caster pivots.

3.Lubricate front caster pivots once a year. Remove hex plug and cap. Thread grease zerk in hole and pump with grease until it oozes out around top bearing. Remove grease zerk and thread plug back in. Place cap back on.

Lubricate Caster Wheel Hubs

Service Interval: As required

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

35

Image 35

Contents Lazer Z Advantage Series X Models California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0752 Systems SpecificationsModel Numbers Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsOverall Height DimensionsOverall Width Overall LengthWheel Base Center of Caster Tire to Center of Drive Tire Curb WeightAccessory Weight Table Worksheet Tread Width Center to Center of Tires, WidthwiseTorque Requirements Product OverviewControls OperationFuel Gauge Ignition SwitchFuel Shut-Off Valve Hour MeterDo Not tow machine PTO Engagement SwitchLow Voltage Indicator Drive Wheel Release ValvesTransport Lock Pre-StartOperating Instructions Deck Lift PedalStarting the Engine Open the Fuel Shut-Off ValveDriving the Machine Engaging the PTODisengaging the PTO Stopping the EngineDriving in Reverse Adjusting the Cutting HeightDriving Forward Transporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Recommended Maintenance Schedules MaintenanceProposition 65 Warning Check Battery ChargeCheck Engine Oil Level Do Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Rollover Protections Systems Roll Bar Knobs Check Safety Interlock SystemChange Engine Oil Service Air CleanerCheck Seat Belt Check for Loose HardwareLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsStyle a black finish Wheel Hub Slotted Nut Torque SpecificationChange Hydraulic System Filter and Fluid Style B yellow zinc Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyChange Engine Coolant Kawasaki Liquid-Cooled Only Thread Locking Adhesives Check Spark Arrester if equippedDeck Leveling Copper-Based Anti-seizeDielectric Grease Adjuster screw Yoke 4 inches 8.3 cm Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Start the mower while in the operator position Removing the Shim Electric Clutch AdjustmentMotion Control Linkage Adjustment Adjusting the height Motion Control Damper AdjustmentMotion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentAdjusting the Tilt Caster Pivot Bearings Pre-Load AdjustmentClean Debris From Machine Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling FinsMotor Oil Disposal Battery DisposalWaste Disposal Problem Possible Cause Corrective Action TroubleshootingRefer to Check Engine Coolant Level Troubleshooting Electrical Diagram Air-Cooled SchematicsTAN Electrical Diagram Liquid-CooledElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options