Exmark Series X manual Loading a Unit

Page 28

Operation

CAUTION

This unit does not have proper turn signals, lights, reflective markings, or a slow moving vehicle emblem. Driving on a street or roadway without such equipment is dangerous and can lead to accidents causing personal injury. Driving on a street or roadway without such equipment may also be a violation of State laws and the operator may be subject to traffic tickets and/or fines.

Do Not drive a unit on a public street or roadway.

WARNING

Loading a unit on a trailer or truck increases the possibility of backward tip-over. Backward tip-over could cause serious injury or death.

Use extreme caution when operating a unit on a ramp.

Use only a single, full width ramp; Do Not use individual ramps for each side of the unit.

If individual ramps must be used, use enough ramps to create an unbroken ramp surface wider than the unit.

Do Not exceed a 15° angle between ramp and ground or between ramp and trailer or truck.

Avoid sudden acceleration while driving unit up a ramp to avoid tipping backward.

Avoid sudden deceleration while backing unit down a ramp to avoid tipping backward.

Loading a Unit

Use extreme caution when loading units on trailers or trucks. One full width ramp that is wide enough to extend beyond the rear tires is recommended instead of individual ramps for each side of the unit. The lower rear section of the tractor frame extends back between the rear wheels and serves as a stop for tipping backward. Having a full width ramp provides

a surface for the frame members to contact if the unit starts to tip backward. If it is not possible to use one full width ramp, use enough individual ramps to simulate a full width continuous ramp.

Ramp should be long enough so that the angles between the ramp and the ground and the ramp and the trailer or truck do not exceed 15°. A steeper angle may cause mower deck components to get caught as the unit moves from ramp to trailer or truck. Steeper angles may also cause the unit to tip backward. If loading on or near a slope, position the trailer or truck so it is on the down side of the slope and the ramp extends up the slope. This will minimize the ramp angle. The trailer or truck should be as level as possible.

Important: Do Not attempt to turn the unit while on the ramp, you may lose control and drive off the side.

Avoid sudden acceleration when driving up a ramp and sudden deceleration when backing down a ramp. Both maneuvers can cause the unit to tip backward.

28

Image 28
Contents Lazer Z Advantage Series X Models California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0752 Model Numbers SpecificationsSystems Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Overall WidthOverall Length Overall HeightCurb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsIgnition Switch Fuel Shut-Off ValveHour Meter Fuel GaugePTO Engagement Switch Low Voltage IndicatorDrive Wheel Release Valves Do Not tow machinePre-Start Operating InstructionsDeck Lift Pedal Transport LockOpen the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineDriving Forward Adjusting the Cutting HeightDriving in Reverse Transporting Adjusting the Anti-Scalp RollersTransporting a Unit Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Engine Oil Level Check Battery ChargeProposition 65 Warning Recommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existCheck Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsService Air Cleaner Check Seat BeltCheck for Loose Hardware Change Engine OilCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterChange Hydraulic System Filter and Fluid Wheel Hub Slotted Nut Torque SpecificationStyle a black finish Change Engine Coolant Kawasaki Liquid-Cooled Only Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyStyle B yellow zinc Check Spark Arrester if equipped Thread Locking AdhesivesDielectric Grease Copper-Based Anti-seizeDeck Leveling Adjuster screw Yoke 4 inches 8.3 cm Pump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Start the mower while in the operator position Electric Clutch Adjustment Removing the ShimMotion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Adjusting the heightCaster Pivot Bearings Pre-Load Adjustment Adjusting the TiltClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Fins Clean Debris From MachineWaste Disposal Battery DisposalMotor Oil Disposal Troubleshooting Problem Possible Cause Corrective ActionRefer to Check Engine Coolant Level Troubleshooting Schematics Electrical Diagram Air-CooledElectrical Diagram Liquid-Cooled TANElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options