Exmark Series X manual Specifications, Model Numbers, Systems

Page 15

Specifications

Specifications

Model Numbers

Serial Nos: 850,000 and Higher

LZAS22KA484; LZAS22KA484CA; LZAS23KC524; LZAS25KC604; LZAS26LKA604; LZAS27KC524; LZAS27KC524CA; LZAS27KC604; LZAS27KC604CA; LZAS29KA724

Systems

Engine

•Engine Specifications: See your Engine Owner’s Manual

•RPM: Full Speed: 3750 ±50 RPM (PTO not

engaged) Idle: 1500 ±100 RPM

Fuel System

•Capacity: 12.0 gal. (45.4 L)

•Type of Fuel: Regular unleaded gasoline, 87 octane or higher; containing no more than 10% methanol or ethanol.

•Fuel Filter:

–Kohler:

Kohler P/N 24 050 13

–Kawasaki:

Kawasaki P/N 49019-7005

•Fuel Shut-Off Valve:

All Units: 1/4 turn increments (“ON”, “OFF”).

•Fuel level eight segment display — right hand control panel.

•Low fuel indicator light.

Electrical System

•Charging System: Flywheel Alternator

•Charging Capacity:

–Kohler and Kawasaki Air-Cooled: 15 amps

–Kawasaki Liquid-Cooled: 20 amps

•Battery Type: BCI Group U1

•Recommended Minimum Battery CCA: 260 CCA

•Battery Voltage: 12 Volt

•Low Voltage Light — RH control panel

•Polarity: Negative Ground

•Fuses:

All units:

–25 amp main fuse

–25 amp charging system fuse

–10 amp PTO fuse

–15 amp accessory fuse

Safety Interlock System

•LCD indicators appear for the PTO, park brake, drive levers, and operator presence in the message display on the RH control panel.

•PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

•Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

•Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Cooling System (Kawasaki

Liquid-Cooled Only)

•Fan: Continuous operation with engine running.

•Coolant Liquid: 50/50 mix of DexCool© extended life antifreeze and water.

•Coolant Capacity: 3.1 quarts

Operator Controls

•Steering and Motion Control:

Note: Motion control levers are adjustable to two heights.

–Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

–Steering is controlled by varying the position of the levers relative to each other.

15

Image 15

Contents Lazer Z Advantage Series X Models California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0752 Specifications Model NumbersSystems Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsOverall Height DimensionsOverall Width Overall LengthWheel Base Center of Caster Tire to Center of Drive Tire Curb WeightAccessory Weight Table Worksheet Tread Width Center to Center of Tires, WidthwiseTorque Requirements Product OverviewControls OperationFuel Gauge Ignition SwitchFuel Shut-Off Valve Hour MeterDo Not tow machine PTO Engagement SwitchLow Voltage Indicator Drive Wheel Release ValvesTransport Lock Pre-StartOperating Instructions Deck Lift PedalStarting the Engine Open the Fuel Shut-Off ValveDriving the Machine Engaging the PTODisengaging the PTO Stopping the EngineAdjusting the Cutting Height Driving ForwardDriving in Reverse Adjusting the Anti-Scalp Rollers TransportingTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Battery Charge Check Engine Oil LevelProposition 65 Warning Do Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Rollover Protections Systems Roll Bar Knobs Check Safety Interlock SystemChange Engine Oil Service Air CleanerCheck Seat Belt Check for Loose HardwareLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsWheel Hub Slotted Nut Torque Specification Change Hydraulic System Filter and FluidStyle a black finish Check Engine Coolant Level Kawasaki Liquid-Cooled Only Change Engine Coolant Kawasaki Liquid-Cooled OnlyStyle B yellow zinc Thread Locking Adhesives Check Spark Arrester if equippedCopper-Based Anti-seize Dielectric GreaseDeck Leveling Adjuster screw Yoke 4 inches 8.3 cm Adjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension Start the mower while in the operator position Removing the Shim Electric Clutch AdjustmentMotion Control Linkage Adjustment Adjusting the height Motion Control Damper AdjustmentMotion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentAdjusting the Tilt Caster Pivot Bearings Pre-Load AdjustmentClean Debris From Machine Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling FinsBattery Disposal Waste DisposalMotor Oil Disposal Problem Possible Cause Corrective Action TroubleshootingRefer to Check Engine Coolant Level Troubleshooting Electrical Diagram Air-Cooled SchematicsTAN Electrical Diagram Liquid-CooledElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options