Exmark Series X manual Seat, Hydrostatic Ground Drive System, Tires & Wheels, Cutting Deck

Page 16

Specifications

Moving motion control levers outward (in slots) locks the drive system in neutral.

PTO Engagement Switch: Engages electric clutch (to drive belt) which engages mower blades.

Parking Brake Lever: Engages parking brake.

Parking Brake Release Button: Releases parking brake.

Deck Height Adjustment Lever: Sets cutting height to desired position.

Deck Lift Pedal: Foot pedal that lifts deck.

Transport Lock:

Latching position: Automatically latches at the transport position.

Unlatching position: Deck does not latch at the transport position.

Seat

Type: Standard seat with high back, extra wide foam padded seat cushion with internal suspension, thick bolstering, armrests, integral safety switch.

Optional seat accessories for units with standard seats:

Custom ride suspension system to enhance Standard Seat. Adds approximately 3 inches (7.6 cm) to seat height.

Deluxe suspension seat with high back, low profile foam-in-place cushion (dampened, adjustable spring suspension), armrests, and integral safety switch. Seat height remains the same.

Seat Isolation System for reduced vibration, to enhance ride of standard seat, standard seat with Custom Ride Seat Suspension or Deluxe Suspension Seat. Adds approximately 1 inch (2.5 cm) to seat height.

Mounting: Adjustable fore and aft on seat tracks.

Armrests:

Standard seat: foam padded adjustable flip-up armrests.

Suspension seat: molded adjustable flip-up armrests.

Seat Safety Switch:

Integrated seat switch. Time delay seat switch eliminates rough ground cut-outs.

Hydrostatic Ground Drive System

Two unitized hydrostatic transmissions: 12cc Parker axial piston pump

240cc Parker geroler motor

Hydraulic Oil Type: Exmark Premium Hydro oil.

Hydraulic Oil Capacity: 52 oz (1.5 L) per side

Hydraulic Filter: P/N 116-0164

Speeds:

0-10 mph (16.1 km/hr) forward.

0-5.5 mph (8.9 km/hr) reverse.

Drive wheel release valves allow machine to be moved when engine is not running.

Tires & Wheels

 

 

Drive

 

 

 

 

Pneumatic (Air filled)

 

 

 

 

Deck Size

48 & 52

 

60 & 72

Quantity

2

 

2

 

 

 

 

Tread

Turf Master

 

Turf Master

 

 

 

 

Size

24 x 9.50-12

 

24 x 12.00-12

 

 

 

 

Ply Rating

4

 

4

Pressure

13 psi (90 kPa)

 

13 psi (90 kPa)

 

 

 

Front Caster

 

Pneumatic (Air filled)

Deck Size

48, 52, & 60

 

72

Quantity

2

 

2

 

 

 

 

Tread

Smooth

 

Smooth

 

 

 

 

Size

13 x 5.00-6

 

13 x 6.50-6

Ply Rating

4

 

4

Pressure

13 psi (90 kPa)

 

13 psi (90 kPa)

 

 

 

 

Cutting Deck

Cutting Width:

48 inch Deck: (121.9 cm)

52 inch Deck: (132.1 cm)

60 inch Deck: (152.4 cm)

72 inch Deck: (182.9 cm)

Discharge: Side

Blade Size: (3 ea.)

16

Image 16
Contents Lazer Z Advantage Series X Models California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0752 Model Numbers SpecificationsSystems Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Overall WidthOverall Length Overall HeightCurb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsIgnition Switch Fuel Shut-Off ValveHour Meter Fuel GaugePTO Engagement Switch Low Voltage IndicatorDrive Wheel Release Valves Do Not tow machinePre-Start Operating InstructionsDeck Lift Pedal Transport LockOpen the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineDriving Forward Adjusting the Cutting HeightDriving in Reverse Transporting Adjusting the Anti-Scalp RollersTransporting a Unit Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Engine Oil Level Check Battery ChargeProposition 65 Warning Recommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existCheck Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsService Air Cleaner Check Seat BeltCheck for Loose Hardware Change Engine OilCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterChange Hydraulic System Filter and Fluid Wheel Hub Slotted Nut Torque SpecificationStyle a black finish Change Engine Coolant Kawasaki Liquid-Cooled Only Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyStyle B yellow zinc Check Spark Arrester if equipped Thread Locking AdhesivesDielectric Grease Copper-Based Anti-seizeDeck Leveling Adjuster screw Yoke 4 inches 8.3 cm Pump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Start the mower while in the operator position Electric Clutch Adjustment Removing the ShimMotion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Adjusting the heightCaster Pivot Bearings Pre-Load Adjustment Adjusting the TiltClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Fins Clean Debris From MachineWaste Disposal Battery DisposalMotor Oil Disposal Troubleshooting Problem Possible Cause Corrective ActionRefer to Check Engine Coolant Level Troubleshooting Schematics Electrical Diagram Air-CooledElectrical Diagram Liquid-Cooled TANElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options