Exmark Series X manual Slope Operation, Using the Rollover Protection System Rops

Page 8

Safety

Be aware of the mower discharge path and direct discharge away from others.

Do Not operate the mower under the influence of alcohol or drugs.

Use extreme care when loading or unloading the machine into a trailer or truck.

Use care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

Slope Operation

Use Extreme caution when mowing and/or turning on slopes as loss of traction and/or tip-over could occur. The operator is responsible for safe operation on slopes.

DANGER

Operating on wet grass or steep slopes can cause sliding and loss of control. Wheels dropping over edges, ditches, steep banks, or water can cause rollovers, which may result in serious injury, death or drowning.

Do Not mow slopes when grass is wet.

Do Not mow near drop-offs or near water.

Do Not mow slopes greater than 15 degrees.

Reduce speed and use extreme caution on slopes.

Avoid sudden turns or rapid speed changes.

Keep the roll bar in the raised and locked position and use seat belt.

See inside the back cover to determine the approximate slope angle of the area to be mowed.

Use a walk behind mower and/or a hand trimmer near drop-offs, ditches, steep banks or water. (Figure 3).

Figure 3

1.Safe Zone-Use the mower here on slopes less than 15 degrees

2.Danger Zone-Use a walk behind mower and/or hand trimmer on slopes greater than 15 degrees, near drop-offs and water.

3.Water

Remove or mark obstacles such as rocks, tree limbs, etc. from the mowing area. Tall grass can hide obstacles.

Watch for ditches, holes, rocks, dips and rises that change the operating angle, as rough terrain could overturn the machine.

Avoid sudden starts when mowing uphill because the mower may tip backwards.

Be aware that operating on wet grass, across steep slopes or down hill may cause the mower to lose traction. Loss of traction to the drive wheels may result in sliding and loss of braking and steering.

Always avoid sudden starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly off the slope.

Follow the manufacturer’s recommendations for wheel weights or counter weights to improve stability.

Use extreme care with grass catchers or attachments. These can change the stability of the machine and cause loss of control.

Using the Rollover Protection System (ROPS)

A Rollover Protection System (roll bar) is installed on the unit.

8

Image 8
Contents Lazer Z Advantage Series X Models California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0752 Systems SpecificationsModel Numbers Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Overall WidthOverall Length Overall HeightCurb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsIgnition Switch Fuel Shut-Off ValveHour Meter Fuel GaugePTO Engagement Switch Low Voltage IndicatorDrive Wheel Release Valves Do Not tow machinePre-Start Operating InstructionsDeck Lift Pedal Transport LockOpen the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineDriving in Reverse Adjusting the Cutting HeightDriving Forward Transporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Maintenance Recommended Maintenance SchedulesProposition 65 Warning Check Battery ChargeCheck Engine Oil Level Recommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existCheck Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsService Air Cleaner Check Seat BeltCheck for Loose Hardware Change Engine OilCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterStyle a black finish Wheel Hub Slotted Nut Torque SpecificationChange Hydraulic System Filter and Fluid Style B yellow zinc Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyChange Engine Coolant Kawasaki Liquid-Cooled Only Check Spark Arrester if equipped Thread Locking AdhesivesDeck Leveling Copper-Based Anti-seizeDielectric Grease Adjuster screw Yoke 4 inches 8.3 cm Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Start the mower while in the operator position Electric Clutch Adjustment Removing the ShimMotion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Adjusting the heightCaster Pivot Bearings Pre-Load Adjustment Adjusting the TiltClean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Fins Clean Debris From MachineMotor Oil Disposal Battery DisposalWaste Disposal Troubleshooting Problem Possible Cause Corrective ActionRefer to Check Engine Coolant Level Troubleshooting Schematics Electrical Diagram Air-CooledElectrical Diagram Liquid-Cooled TANElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options