Exmark Series X manual California

Page 2

WARNING

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

Important: The engine in this product is not equipped with a spark arrester muffler. It is a violation of California Public Resource Code (CPRC) Section 4442 to use or operate this engine on any forest-covered, brush-covered, or grass-covered land as defined in CPRC 4126. Other states or federal areas may have similar laws.

To acquire a spark arrester for your unit, see your Engine Service Dealer.

This spark ignition system complies with Canadian ICES-002 Ce système d’allumage par ètincelle de vèhicule est conforme à la norme NMB-002 du Canada.

The enclosed Engine Owner’s Manual is supplied for information regarding The U.S. Environmental Protection Agency (EPA) and the California Emission Control Regulation of emission systems, maintenance and warranty.

Keep this engine Owner’s Manual with your unit. Should this engine Owner’s Manual become damaged or illegible, replace immediately. Replacements may be ordered through the engine manufacturer.

Exmark reserves the right to make changes or add improvements to its products at any time without incurring any obligation to make such changes to products manufactured previously. Exmark, or its distributors and dealers, accept no responsibility for variations which may be evident in the actual specifications of its products and the statements and descriptions contained in this publication.

© 2010—Exmark Mfg. Co., Inc.

 

Contact us at www.Exmark.com.

Industrial Park Box 808

 

Printed in the USA

2

Beatrice, NE 68310

All Rights Reserved

Image 2
Contents Lazer Z Advantage Series X Models California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0752 Systems SpecificationsModel Numbers Tires & Wheels SeatHydrostatic Ground Drive System Cutting DeckOverall Length DimensionsOverall Width Overall HeightTread Width Center to Center of Tires, Widthwise Curb WeightAccessory Weight Table Worksheet Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsHour Meter Ignition SwitchFuel Shut-Off Valve Fuel GaugeDrive Wheel Release Valves PTO Engagement SwitchLow Voltage Indicator Do Not tow machineDeck Lift Pedal Pre-StartOperating Instructions Transport LockOpen the Fuel Shut-Off Valve Starting the EngineStopping the Engine Engaging the PTODisengaging the PTO Driving the MachineDriving in Reverse Adjusting the Cutting HeightDriving Forward Transporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Maintenance Recommended Maintenance SchedulesProposition 65 Warning Check Battery ChargeCheck Engine Oil Level Recommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existCheck Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsCheck for Loose Hardware Service Air CleanerCheck Seat Belt Change Engine OilLubricate Grease Fittings Check Tire PressuresCheck Condition Of Belts Lubricate Caster Wheel HubsCheck Spark Plugs Lubricate Brake Handle PivotLubricate Deck Lift Pivot Change Fuel FilterStyle a black finish Wheel Hub Slotted Nut Torque SpecificationChange Hydraulic System Filter and Fluid Style B yellow zinc Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyChange Engine Coolant Kawasaki Liquid-Cooled Only Check Spark Arrester if equipped Thread Locking AdhesivesDeck Leveling Copper-Based Anti-seizeDielectric Grease Adjuster screw Yoke 4 inches 8.3 cm Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Start the mower while in the operator position Electric Clutch Adjustment Removing the ShimMotion Control Linkage Adjustment Motion Control Handle Adjustment Motion Control Damper AdjustmentMotion Control Neutral Lock Pivot Adjustment Adjusting the heightCaster Pivot Bearings Pre-Load Adjustment Adjusting the TiltClean Hydro Fan Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineMotor Oil Disposal Battery DisposalWaste Disposal Troubleshooting Problem Possible Cause Corrective ActionRefer to Check Engine Coolant Level Troubleshooting Schematics Electrical Diagram Air-CooledElectrical Diagram Liquid-Cooled TANElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options