Exmark 000 & higher, 312 Check Engine Oil Level, Check Battery Charge, Proposition 65 Warning

Page 27

Maintenance

Maintenance Service

Maintenance Procedure

Interval

 

 

 

Every 500 hours

• Change the hydraulic filter (Every 250 hours/yearly if using Mobil 1 15W50)

• Check wheel hub-slotted torque specification.

 

 

 

Monthly

• Check the battery charge.

• Grease the PTO engagement bellcrank.

 

 

 

Periodic Maintenance

Check Engine Oil Level

Service Interval: Before each use or daily

1.Stop engine and wait for all moving parts to stop. Make sure unit is on a level surface.

2.Check with engine cold.

3.Clean area around dipstick. Remove dipstick and wipe oil off. Reinsert the dipstick and push it all the way down into the tube. Do Not screw into place. Remove the dipstick and read the oil level.

4.If the oil level is low, wipe off the area around the oil fill cap, remove cap and fill to the “FULL” mark on the dipstick. Exmark 4-Cycle Premium Engine Oil is recommended; refer to the Engine Owner's manual for an acceptable alternative. Do Not overfill.

Important: Do Not operate the engine with the oil level below the “LOW” (or “ADD”) mark on the dipstick, or over the “FULL” mark.

Check Battery Charge

Service Interval: Monthly

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

Allowing batteries to stand for an extended period of time without recharging them will result in reduced performance and service life. To preserve optimum battery performance and life, recharge batteries in

storage when the open circuit voltage drops to 12.4 volts.

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

Important: Make sure the negative battery cable is disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart for recommended charger settings).

Voltage

Percent

Maximum

Charging

Reading

Charge

Charger

Interval

 

 

Settings

 

12.6 or

100%

16 volts/7

No

greater

 

amps

Charging

 

 

 

Required

12.4 – 12.6

75–100%

16 volts/7

30 Minutes

 

 

amps

 

12.2 – 12.4

50–75%

16 volts/7

1 Hour

 

 

amps

 

12.0–12.2

25–50%

14.4 volts/4

2 Hours

 

 

amps

 

11.7–12.0

0–25%

14.4 volts/4

3 Hours

 

 

amps

 

11.7 or less

0%

14.4 volts/2

6 Hours or

 

 

amps

More

Recommended Jump

Starting Procedure

Service Interval: As required

1.Check the weak battery for terminal corrosion (white, green, or blue “snow”), it must be cleaned

27

Image 27
Contents Turf Tracer Series LP All Rights Reserved Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety With each tank change InspectionOperation WeeklyTank Requalification Slope Operation Maintenance and StorageSafety Safety Safety and Instructional Decals 553049 98-5954 103-1798 103-1976 103-2076 103-2103 103-2242 103-2243 103-4935 109-3148 109-9870 109-9875 116-0404 117-2718 109-9906 Specifications Model NumbersSystems Dimensions Torque Requirements Product OverviewControls OperationPre-Start Disengaging the PTO Operating InstructionsOpen the Fuel Valve Starting the EngineDriving the Machine Drive Lever/Neutral Lock Latch OperationDriving Forward Driving in Reverse Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers TransportingTransporting a Unit Operation Recommended Maintenance Schedules MaintenanceProposition 65 Warning Check Battery ChargeRecommended Jump Starting Procedure Check Engine Oil LevelCheck Mower Blades Do Not jump start a weak battery if these conditions existReplacing the Discharge Deflector Check Safety Interlock System Service Pre-Cleaner Element and Air CleanerCheck for Loose Hardware Check Condition Of Belts Change Engine OilCheck Hydraulic Oil Level Check Tire PressuresChange LPG Tank Check LPG TankCheck LPG Fuel Delivery System Check Spark PlugsLevel Change Hydraulic System FilterHydraulic System Air Purge Mobil HTS Grease Or Food-Grade Anti-seize Wheel Hub-Slotted Nut Torque SpecificationInspect PTO Clutching Belt Tension Thread Locking AdhesivesDeck Leveling Park Brake AdjustmentHydro Drive Linkage Adjustment Dielectric GreaseAdjust Hydro Control Linkages Adjust Neutral Control LinkagesNeed to be adjusted Drive Lever Linkage AdjustmentLPG Regulator Tracking AdjustmentHydro Pump Spring Tension Setting PTO Safety SwitchClean Grass Build-Up Under Deck Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineMaintenance Problem Possible Cause Corrective Action TroubleshootingSee Check Spark Plug section Troubleshooting Electrical Diagram SchematicsHydraulic Diagram Exmark Commercial Turf Equipment Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.