Exmark 000 & higher, 312 manual Adjusting the Cutting Height, Driving in Reverse

Page 23

Operation

Driving in Reverse

To move rearward in a straight line, squeeze drive levers into the reverse position.

To turn left or right, squeeze the right hand drive lever to turn left and the left hand drive lever to turn right.

To make a “zero turn”, squeeze either the left hand or the right hand drive lever back into the reverse position while the opposite drive lever is in a forward position at an equal but opposite speed.

Note: For smooth operation of this machine, avoid quick, jerky movements of the drive levers. Move the drive levers smoothly and deliberately.

To stop, squeeze drive levers back to the “neutral” position. Move the neutral lock latches into the “neutral lock” position and release drive levers. Move the speed control lever to the neutral position.

Adjusting the Cutting Height

WARNING

When the two front support rod hairpins are removed from the mower deck, the weight of the tractor section may cause the front frame of the unit to rise suddenly. If the unit rises suddenly, injury may occur.

Securely hold down the front of the unit when the front support rod hairpins are removed.

The cutting height of the mower deck is adjusted from 1 1/2 to 4 1/2 inches (3.81 cm to 11.4 cm) in 1/2 inch increments.

1.Stop the machine and move the drive levers to the neutral locked position.

2.Disengage the PTO.

3.Engage the park brake.

4.Stop the engine, remove the key and wait for all moving parts to stop.

5.Install hairpin clips in the holes for the desired cutting height. See Figure 6.

Important: To maintain correct cutting height and rake, check the following for proper adjustment.

A.The front and rear hairpins are in the same holes with the proper spacers under the hair pins. See Figure 6.

Figure 6

1. Deck support pin

2. Cutting Height

B.The tire pressures are set as directed in Check Tire Pressures in the Maintenance section.

C.The length of the rear deck support link assemblies average 6.89 inches (approximately 6 7/8 inches) (175.01 mm) from the center of the balljoint to the center of the farthest hole. See Figure 7.

Note: All four pins must equally support the weight of the deck. Adjustment in the length of the rear deck support assemblies may be necessary. If one side is longer than 6.89 inches (approximately 6 7/8 inches) (175.01 mm), than the opposite side must be shorter by the same amount.

Figure 7

Left Hand Side Shown

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Turf Tracer Series LP All Rights Reserved Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety With each tank change InspectionTank Requalification OperationWeekly Slope Operation Maintenance and StorageSafety Safety Safety and Instructional Decals 553049 98-5954 103-1798 103-1976 103-2076 103-2103 103-2242 103-2243 103-4935 109-3148 109-9870 109-9875 116-0404 117-2718 109-9906 Systems SpecificationsModel Numbers Dimensions Torque Requirements Product OverviewControls OperationPre-Start Disengaging the PTO Operating InstructionsOpen the Fuel Valve Starting the EngineDriving Forward Driving the MachineDrive Lever/Neutral Lock Latch Operation Driving in Reverse Adjusting the Cutting HeightTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Operation Recommended Maintenance Schedules MaintenanceProposition 65 Warning Check Battery ChargeRecommended Jump Starting Procedure Check Engine Oil LevelCheck Mower Blades Do Not jump start a weak battery if these conditions existReplacing the Discharge Deflector Check for Loose Hardware Check Safety Interlock SystemService Pre-Cleaner Element and Air Cleaner Check Condition Of Belts Change Engine OilCheck Hydraulic Oil Level Check Tire PressuresChange LPG Tank Check LPG TankCheck LPG Fuel Delivery System Check Spark PlugsLevel Change Hydraulic System FilterHydraulic System Air Purge Mobil HTS Grease Or Food-Grade Anti-seize Wheel Hub-Slotted Nut Torque SpecificationInspect PTO Clutching Belt Tension Thread Locking AdhesivesDeck Leveling Park Brake AdjustmentHydro Drive Linkage Adjustment Dielectric GreaseAdjust Hydro Control Linkages Adjust Neutral Control LinkagesNeed to be adjusted Drive Lever Linkage AdjustmentLPG Regulator Tracking AdjustmentHydro Pump Spring Tension Setting PTO Safety SwitchClean Grass Build-Up Under Deck Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineMaintenance Problem Possible Cause Corrective Action TroubleshootingSee Check Spark Plug section Troubleshooting Electrical Diagram SchematicsHydraulic Diagram Exmark Commercial Turf Equipment Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents