GE GNSF48A01 manuals
Household Appliance > Water System
When we buy new device such as GE GNSF48A01 we often through away most of the documentation but the warranty.
Very often issues with GE GNSF48A01 begin only after the warranty period ends and you may want to find how to repair it or just do some service work.
Even oftener it is hard to remember what does each function in Water System GE GNSF48A01 is responsible for and what options to choose for expected result.
Fortunately you can find all manuals for Water System on our side using links below.
GE GNSF48A01 Installation Instructions
36 pages 781.69 Kb
GNSF39A01 GNSF48A01 GE Applianceswww.geappliances.com 215C1044P005-3 49-50020-3 04/00 JR 7221039 Safety Information Installation Instructions Operating Instructions, Tips Care and Cleaning Troubleshooting Tips Customer Service Water SofteningsystemOwners Manual & Installation Instructions 2 GE & You, A Service Partnership.FOR YOUR RECORDSWrite the model and serial numbers here:www.geappliances.com Troubleshooting Tips # #Staple sales slip or cancelled check here. READ THIS MANUAL IF YOU NEED SERVICEBefore You Call For Service OR IMPORTANT!Two easy ways to register your appliance! 3 WARNING! electric shock, property damage or personal injury.WARNING: lead-free solder and flux Do not WARNING: SAFETY PRECAUTIONSBe sure to use only the included transformer. Read and follow this Safety Information carefully. SAVE THESE INSTRUCTIONS PROPER INSTALLATION IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. 4 Installation instructions.Unpacking and Inspection Important Installation Recommendations 5 Where to Install the SoftenerPlan How You Will Install the Softener Tools and Materials Required for Installation 6 Installation instructions.Typical Installation IllustrationMAIN WATER PIPE NOTE: Fig. 1 Optional 3-Valve Bypass Installation IllustrationFig. 2 MAIN WATER PIPE Drain Hose Connections to keep the weight off of the valve fittings. Connect and run the valve drain hose: IMPORTANT: Do all sweat soldering before between the end of the hose and the drain point. IMPORTANT: Check and comply with local codes.Also provide an air gap of at least 11/2 do not raise higher than 8 above the floor. Install bypass valve: NOTE: Move the softener assembly into installation position: CAUTION: Plumb IN and OUT pipes to and from softener: CAUTION: connecting pipes to the bypass valve. use care not to cross-thread. 7 Fig. 3 Fig. 4 8 Fig. 6Fig. 5 DATA 9 Programming the ControlSet present time of day Set water hardness number 10 Sanitizing ProceduresTo complete the installation, do the following sanitizing procedures. Recharge Now TOUCH/HOLD IMPORTANT: brinewell NOTE: Sanitizing is recommended by the Water Quality Association for disinfecting. . Specifications/DimensionsSee rating decal, located on the Water Softening System. 11 {12 ServiceFILL, BRINING, BRINE RINSE, BACKWASH down up FASTRINSE Automatic Hard Water Bypass During RegenerationHowever, you should avoid using HOT water because the water heater will fill with the hard water. Fill Brining Brine Rinse Backwash Fast Rinse 13 Breaking a Salt Bridge14 Cleaning the Nozzle and Venturi AssemblyA clean nozzle and venturi is needed for the water softening system to work properly. NOTE: Install and tighten the cap, by hand only. Do not over-tighten the cap. 15 Normal Operation, Timer DisplayFeature: Optional Recharge Controls Feature: Program Memory Feature/Service: Automatic Electronic Diagnostics 16 DATA 22 Care and cleaning of the water softening system.Checking the Salt Storage Level and Refilling Cleaning Iron Out of the Water Softening System 23 Before you call for serviceSalt Bridge, water not in contact with salt (see Breaking a Salt Bridge sectionCleaning the Nozzle and Venturi Assembly Program Memory For example, a single lever kitchen faucet, that does not mix soft and hard water. Be sure sample is from a faucet Problem Possible Causes What To Do No soft water if the cold side is plumbed to hard water TOUCH or HOLDNOTE: The electrical outlet for the softener should be continuously so it cannot be accidentally switched off. NO SOFT WATER Most Common Problems:Check the following before calling for service Salt in softener...at least 1/3 full. By pass valve in Service position. Knob should be in the OUT position. 24 Before you call for service26 Parts list.flow plug assembly assembled view 27 {28 Parts catalog.29 *NOTE: General Electric CompanyWarranty Registration Department P.O. Box 32150 Louisville, KY 40232-2150 GE Service Protection Plus 33 Please place in envelope and mail to: Well Cover Any Appliance. Anywhere. Anytime.* 34 Consumer Product Ownership RegistrationFollow these three steps to protect your new appliance investment: Model Number Serial NumberFor The Period Of: GE Will Replace: 35 GE Water Softening System WarrantyWarrantor: General Electric Company. Louisville, KY 40225All warranty service provided by our Factory Service Centers, or an authorized Customer Care technician. For service, call 800-GE-CARES. What GE Will Not Cover: 36 Service Telephone Numbers. GE Answer CenterParts and Accessories Service Contracts Special Needs Service In-Home Repair Service www.geappliances.com 800.626.2000 800-GE-CARES (800-432-2737) 800.626.2000 800-TDD-GEAC (800-833-4322) 800-626-2224 800-626-2002 Service Satisfaction
Also you can find more GE manuals or manuals for other Household Appliance.