Manuals / 321 Studios / Kitchen Appliance / Coffeemaker

321 Studios FH110D48E warranty Oil Furnace Installation Instructions, For Your Safety, Models

Models: FH110D60E FH085D36E FLR110D60E FLR085D36E FLR110D48E FC085D36E FLF110D60E FLF085D36E FLR140D60E FH110D48E FLF110D48E

1 39

Download 39 pages 2.46 Kb

Page 1

OIL FURNACE

OIL FURNACE

INSTALLATION INSTRUCTIONS

MODELS

FH085D36E FH110D48E FH110D60E

FLF085D36E FLF110D48E FLF110D60E

FLR085D36E FLR110D48E FLR110D60E

FLR140D60E FC085D36E

WARNING

READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION.

THIS INSTALLATION MUST COMPLY WITH THESE INSTRUCTIONS AND THE REQUIREMENTS OF ALL GOVERNING CODES AND ORDINANCES FOR THE INSTALLATION LOCATION.

IT IS THE RESPONSIBILITY OF INSTALLER TO KNOW AND UNDERSTAND ALL OF THESE REQUIREMENTS.

FAILURE TO DO SO COULD CREATE A HAZARD RESULTING IN PROPERTY DAMAGE, BODILY INJURY OR DEATH.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

IMPORTANT NOTICE

THIS FURNACE IS NOT INTENDED FOR USE AS A CONSTRUCTION HEATER. USE OF THIS FURNACE DURING CONSTRUCTION AND FINISHING PHASES OF A STRUCTURE IS CONSIDERED AS "OPERATION IN A CORROSIVE ATMOSPHERE" AND "UNUSUAL, NEGLIGENT OR IMPROPER USE" AND AS SUCH ARE CONSIDERED EXCLUSIONS BY THE BARD MANUFACTURING COMPANY LIMITED WARRANTY.

	Bard Manufacturing Company	Manual:	2100-422B
	Bryan, Ohio 43506	Supersedes:	2100-422A
	Since 1914...Moving ahead just as planned.	File:	VOL. I, TAB 3
	Since 1914...Moving ahead just as planned.	Date:	09-23-03
		Date:	09-23-03

Copyright 2003

Image 1

321 Studios FH110D48E, FC085D36E warranty Oil Furnace Installation Instructions, For Your Safety, Important Notice, Models

Contents

FOR YOUR SAFETY OIL FURNACE INSTALLATION INSTRUCTIONSFH085D36E FH110D48E FH110D60E FLF085D36E FLF110D48E FLF110D60E FLR085D36E FLR110D48E FLR110D60E FLR140D60E FC085D36EInstallation and Operating Instructions CONTENTSMaintenance CHARTSFOR MORE INFORMATION, CONTACT THESE PUBLISHERS GETTING OTHER INFORMATION and PUBLICATIONSACCA Air Conditioning Contractors of AmericaEQUIPMENT SELECTION INSTALLATION and OPERATING INSTRUCTIONSLOCATING THE FURNACE MINIMUM CLEARANCESFLF/R MODELS DIMENSIONS SPECIFICATION SHEETFLF/R MODELS DIMENSIONS INCHES FLF/FLR 085, 110 ANDFH MODELS DIMENSIONS FH085 AND FH110 SUPPLY SPECIFICATION SHEETTOP VIEW LEFT SIDE VIEWFC085 MODEL DIMENSIONS SPECIFICATIONFC085 SHEETINSTALLING A COOLING UNIT INSTALLING THE FURNACEINSTRUMENTS REQUIRED FOR PROPER SETUP OF THE FURNACE INSTALLATIONFACTORY WIRING WIRINGFIELD WIRING ELECTRICAL DATAPower Wires Black HOT White NEUTRAL Green GROUND unit power entranceRight side oil line entranceTo power source standards for installing INSTALLER NOTEFollow all appropriate needed venting system1-1/4 Vent Cap 2 Cap 2 Fill PipeVent Pipe GuageBECKETT SOLID STATE IGNITER BECKETT “CLEANCUT” OIL PUMPBECKETT R7184B PRIMARY CONTROL Burner Option - Flame Quality Monitor BECKETT R7184B PRIMARY OPERATIONAL GUIDEElectronic Blower Control Board EBC THERMOSTAT CONNECTIONS HEATING BLOWER OFF DELAY ADJUSTMENT IN SECONDS FURNACE DATA BURNER SETUP AND ADJUSTMENT PROCEDURES1. PREPARATION STEPS Lock the air adjustment and repeat draft 2. COMBUSTION ADJUSTMENT STEPSCO2 and smoke measurements to make sure the setting has not shifted J. Develop Smoke - CO2 Curve Record4. FINAL CHECKS SHORT FORM ADJUSTMENT PROCEDURE2, CHECK DRAFT 3. SMOKE TESTsetting Air SettingsTYPICAL SMOKE - CO2 CHART WITH ADJUSTMENT RANGE HighRemove Bleed Port to attach pressure guage Pressure Gauge MIS-1660PRESSURE GAUGE CONNECTION TO BLEED PORT RECOMMENDED START-UP SETTINGS NO. 2 FUEL OIL EFFICIENCY CHART NET STACK TEMP. DEGREES FCORRELATION OF PERCENT OF CO2, O2 AND RESERVE AIR REMOVING GUN ASSEMBLY GUN ASSEMBLY ADJUSTMENTELECTRODE ADJUSTMENTS COMBUSTION AIR REQUIREMENTSASSEMBLE INNER AIR BOOT REMOVE KNOCKOUT IN LEFT SIDE INSERT OUTER AIR USE THIS KNOCKOUT FOR OIL LINE BURNER ASSEMBLY REMOVE PUMP TOBOOT AND SECURE FLANGE TO UNIT MAKE ALL SETTINGSAPPLIANCES LOCATED IN CONFINED SPACES APPLIANCES LOCATED IN CONFINED SPACESALL AIR FROM INSIDE THE BUILDING SQUARE FEET REQUIRED TO QUALIFY AS UNCONFINED SPACEALL VENTILATION AIR FROM OUTDOORS MINIMUM VENTILATION OPENINGSAPPLIANCES LOCATED IN CONFINED SPACES ALL AIR FROM OUTDOORS MIS-1337ALL AIR FROM OUTDOORS THROUGH VENTILATED ATTIC APPLIANCES LOCATED IN CONFINED SPACESAPPLIANCES LOCATED IN CONFINED SPACES ALL AIR FROM OUTDOORS MIS-1338VENTING OPTIONS LOUVERS AND GRILLESTHERMOSTAT VERTICAL VENTINGAND HEATING BLOWER SPEEDS TEMPERATURE RISE RANGES, LIMIT CONTROL SETTINGSMaximum Outlet AirTYPICAL INSTALLATION OF FR26 AND FR27 FILTER RACKS AIR FILTERSTYPICAL INSTALLATION OF FR25 FILTER KIT FC UnitSTEP STEP SLIDE FILTER OUT TOWARDS BLOWER DOORUNFASTEN SWELL BY PULLING OUT ONSERVICE HINTS MAINTENANCELUBRICATION INSPECT AIR FILTERBOOT OPTIONAL AND OIL DISCONNECT T-T WIRESDANGER COMBINATION COMBUSTION CHAMBER/BURNER MOUNTING SYSTEMSTEP PULL BURNER ASSEMBLY STRAIGHT OUT TO PREVENT DAMAGE TO CHAMBER DANGEROF BURNER PLATE STEP DISCONNECT T-T WIRES POWER CONNECTIONS, AIR MIS-1837 BOOT OPTIONAL AND OIL LINES TO BURNERCOMMON CAUSES OF TROUBLE CLEANING OF THE HEAT EXCHANGERCARE OF FINISH BURNER WILL NOT PRODUCE FLAMECHART FH085D36E DATA BLOWER SYSTEM RESISTANCE CHARTSCHART FH110D48E DATA CHART FH110D60E DATACHART FC085D36E DATA CHART FLR140D60E DATABlower Speed Blower StaticDANGER 4047-118 BFH SERIES WIRING DIAGRAM FLF/R SERIES WIRING DIAGRAM 4047-119 CUNIT THERMOSTAT COND UNIT4047-120 B WIRING DIAGRAM