Manuals / 321 Studios / Kitchen Appliance / Coffeemaker

321 Studios FLF085D36E, FH110D48E Minimum Ventilation Openings, ALL Ventilation AIR from Outdoors

Models: FH110D60E FH085D36E FLR110D60E FLR085D36E FLR110D48E FC085D36E FLF110D60E FLF085D36E FLR140D60E FH110D48E FLF110D48E

1 39

Download 39 pages 2.46 Kb

Page 25

TABLE 9

MINIMUM VENTILATION OPENINGS

			Recommended
		Min. Ventilation	Opening
		Min. Ventilation	(2 Required)
		Opening	(2 Required)
	Model	Square Inch	Size	Sq. In.

	FH085D36E	240	8 x 16	128

	FH110D48E	280	9 x 18	162

	FH110D60E	280	9 x 18	162

	FLF085D36E	290	8 x 19	152

	FLR085D36E	290	8 x 19	152

	FLF110D48E	340	9 x 19	171
	FLF110D60E	340	9 x 19	171
	FLF110D60E
	FLR110D48E	340	9 x 19	171
	FLR110D60E	340	9 x 19	171
	FLR110D60E
	FLR140D60E	360	9.5 x 19	180
	FC085D36E	240	8 x 16	128

ALL VENTILATION AIR FROM OUTDOORS

A.The confined space shall be provided with two permanent openings, one in or near the top of the enclosure and one in or near the bottom. The openings shall communicate directly, or by means of ducts with outdoors or to such spaces (crawl or attic) that freely communicate with outdoors. (See Figures 13, 14, & 15.)

B.When directly communicating with outdoors or by means of vertical ducts, each opening shall have a free area of not less than one square inch per 4,000 BTU per hour (35 square inches per gallon per hour) of total input rating of all appliances in the enclosures. If horizontal ducts are used, each opening shall have a free area of not less than one square inch per 2,000 BTU per hour (70 square inches per gallon per hour) of total input of all appliances in the enclosure.

FIGURE 13

APPLIANCES LOCATED IN CONFINED SPACES

ALL AIR FROM OUTDOORS

NOTE: Each air duct opening shall have a free area of not less than one square inch per 2,000 BTU per hour (70 square inches per gallon per hour) of the total input rating of all appliances in the enclosure.

MIS-1337

Manual 2100-422 Page 23

Image 25

321 Studios FLF085D36E, FLF110D48E, FH110D48E, FLR140D60E Minimum Ventilation Openings, ALL Ventilation AIR from Outdoors

Contents

OIL Furnace Installation Instructions Contents For More INFORMATION, Contact These Publishers Getting Other Information and Publications Locating the Furnace Equipment SelectionMinimum Clearances Specification Sheet Supply Specification Sheet FC085 Model Dimensions Specification Sheet Installing a Cooling Unit Installing the FurnaceInstruments Required for Proper Setup of the Furnace Installation Factory Wiring WiringField Wiring Electrical Data Typical Unit Setup FLF Unit Shown I m n e y OIL Line Piping Typical Single Inside Tank InstallationBeckett AFG OIL Burner Beckett Solid State Igniter Beckett Cleancut OIL PumpBeckett R7184B Primary Control Beckett R7184B Primary Operational Guide Electronic Blower Control Cleaner Connection Furnace Data Burner Setup and Adjustment ProceduresPreparation Steps Combustion Diagnosis Combustion Adjustment Steps Final Checks Short Form Adjustment ProcedureCheck Draft Smoke Test Typical Smoke CO2 Chart with Adjustment Range High Air Settings Low Bacharach Smoke Number Pressure Gauge Connection to Bleed Port Recommended START-UP Settings No Fuel OIL Efficiency Chart NET Stack TEMP. Degrees FCorrelation of Percent of CO2, O2 Reserve AIR Removing GUN Assembly GUN Assembly AdjustmentElectrode Adjustments Combustion AIR Requirements Combination AIR Boot Assembly Combustion AIR Boot Assembly Square Feet Required to Qualify AS Unconfined Space Appliances Located in Confined SpacesALL AIR from Inside Building ALL Ventilation AIR from Outdoors Minimum Ventilation OpeningsAppliances Located in Confined Spaces ALL AIR from Outdoors MIS-1338 Venting Options Louvers and GrillesThermostat Vertical Venting 200 Typical Installation of FR25 Filter KIT Typical Installation of FR26 FR27 Filter RacksFilter Sizes for OIL Furnaces LO-BOY Models Filter Locations Filter Installation LO-BOY Models Lubrication Service HintsInspect AIR Filter Final Inspection and Test Removal of Burner only Combination Combustion CHAMBER/BURNER Mounting System To Remove the Entire Combustion Chamber Mounting System To Remove Burner onlyRemoval of Entire Combustion Chamber Mounting System Common Causes of Trouble Cleaning of the Heat ExchangerCare of Finish Chart FH110D48E Data Chart FH085D36E DataChart FH110D60E Data Chart FLF/FLR085D36E Data Chart FC085D36E Data Chart FLR140D60E Data Unit FH Series Wiring Diagram Cond Cond Unit