Manuals / A&D / Computer Equipment / Postal Equipment

A&D MC-10K, MC-30K manual Standard Input And Output Interface, RS-232C and External Contact Input

Models: MC-10K MC-30K

1 68

Download 68 pages 61.31 Kb

Page 44

12. Standard Input And Output Interface

12-1. RS-232C and External Contact Input

D-Sub 25 pin numbers

M2.6

ISO metric screw thread

D-Sub 25 pin assignments

	Pin No.	Signal name	Interface type	Direction	Description
	1	FG		-	Frame ground
	2	RXD	RS-232C	Input	Receive data
	3	TXD	RS-232C	Output	Transmit data
	4	RTS	RS-232C	Input	Ready to send
	5	CTS	RS-232C	Output	Clear to send
	6	DSR	RS-232C	Output	Data set ready
	7	SG	RS-232C / external contact	-	Signal ground
	7	SG	input	-	Signal ground
			input
	18	PRINT	External contact input	Input	Same as the PRINT key
	19	RE-ZERO	External contact input	Input	Same as the RE-ZERO key
	Others	-	-	-	No connection

RS-232C

The balance is a DCE device. Connect the balance to a personal computer (DTE) using a

straight through cable.

Transmission system

: EIA RS-232C

Transmission form

: Asynchronous, bi-directional, half duplex

Transmission rate

: 10 times/second or 5 times/second (same as data refresh rate)

Data format

: Baud rate

: 600, 1200, 2400, 4800, 9600, 19200bps

Data bits

: 7 or 8 bits

Parity

: Even, Odd

(Data bits 7 bits)

None

(Data bits 8 bits)

Stop bit

: 1 bit

(When sending, 2 bits; receiving, 1 bit.

A personal computer will function with either setting.)

Code

: ASCII

RS-232C

-5V to -15V

+5V to +15V

Data bits

Stop bit

Start bit

Parity bit

42

Image 44

A&D MC-10K, MC-30K manual Standard Input And Output Interface, RS-232C and External Contact Input, Sub 25 pin numbers

Contents

MC-10K MC-30K 1WMPD4002203AThis Manual and Marks All rights reservedContents 14-1-1 Averaging Range f1-b and Averaging Time f1-t 14-1-2 10-510-6 About This Manual FeaturesIntroduction Compliance Compliance with the following Council DirectivesUnpacking And Installing The Balance To keep waterproof DustproofAuto-centering Pan AX-MC10K/30KPAN Installation Procedure Installing the Balance EarthPrecautions Before UseDuring Use After UsePower Supply Display Symbols And Key Operation Key When pressed and released When pressed and heldKey Operations DisplayWeighing Units Tael HK general, Singapore Selecting a Weighing Unit Mode WeighingBasic Weighing F1l Filter Used DisplayWhen Building into a System Weighing Speed Adjustment Do not allow vibration or drafts to affect Self Check Function with Response AdjustmentBalance during adjustment Terms CalibrationCalibration Group 150 g ~ +0.159 g Automatic self calibration due to changes in temperatureAutomatic Self Calibration About the internal mass Calibration using the internal massOne-Touch Calibration Calibration Using an External Weight When the MC-10K is usedCalibration Test Using an External Weight Print key...... To store the new weight value. Even ifRemove Remove the weight from the pan Step Balance displays Step Confirm that there is nothing on the pan and pressCorrecting the Internal Mass Value Key Function Switch And Initialization Permit or InhibitTo cancel This operation, press Key Initializing the BalanceStep Press Key Step Press Key to displayCheck the settings and condition before changing parameters Function TableStructure and Sequence of the Function Table Display and Operation KeysDetails of the Function Table Data output mode Cp fnc Cp-bBep LO buzzerTimeout AK, Error codeTime/Date output Dout ID number outputID number setting Internal mass correctionF1-b Averaging range for First moving Average F1-tZero upon power-on p-tr Description of the Class Environment, DisplayCondition Cond Stability band width 5t-bDescription of the Item Data Output Mode Key modeStream mode Auto print modes a and BInterval memory mode Description of the Item Data FormatStandard format 5if type DP Dump print format 5if typeKF format MT formatNU numerical format 5if type CSV formatData number DateTime Tare valueNegative error Data Format ExamplesStable OverloadDisplay character set Setting the ID NumberID Number And GLP Report Calibration report using the internal mass GLP ReportSpace, Ascii 20h Terminator, CR , LF or CRSignature Space, Ascii 20h Calibration report using an external weightCalibration test report using an external weight End block Title block and end blockOperation Standard Input And Output Interface RS-232C and External Contact InputSub 25 pin numbers Sub 25 pin assignmentsOption RS-232C TerminalsExternal contact input Settings Not Auto print polarityNecessary Data output pauseUsing Windows Communication Tools Software WinCT Using the WinCT software, the balance can do the followingRsCom RsKeyCommands Command ListAcknowledge Code and Error Codes Control Using CTS and RTS Settings Related to RS-232CCommand Personal computer Time Balance Command Weighing modeExtended Function Page Page Maintenance Treatment of the BalanceTroubleshooting Checking the Balance Performance and EnvironmentChecking that the balance performs properly Weighing method16-2 Automatic response adjustment zero error Automatic response adjustment unstable errorInternal error Clock battery errorOther Display Asking for RepairSpecifications External Dimensions Unit mmAD-8922A Remote controller Options and Peripheral InstrumentsAX-MC10K/30KPAN Auto-centering Pan AD-8121B PrinterRechargeable Battery Foot SwitchWeighing Environment Logger Data LoggerTerms/Index TermsMemory function Nothing is on the weighing panKeys and symbols IndexError Mode MT formatF1l FUlPage UK Office German Sales OfficeKorea Limited Instruments India Private Limited