Manuals / Brands / Computer Equipment / Postal Equipment / A&D / Computer Equipment / Postal Equipment

A&D MC-10K, MC-30K 1-3. Compliance 1-3-1. Compliance with FCC Rules , 1-3-2. Compliance with EMC Directives

1 68

Download 68 pages, 1.19 Mb

4

1-3. Compliance 1-3-1. Compliance with FCC Rules

Please note that this equipment generates, uses and can radiate radio frequency energy.

This equipment has been tested and has been found to comply with the limits of a Class A

computing device pursuant to Subpart J of Part 15 of FCC rules. These rules are designed

to provide reasonable protection against interference when equipment is operated in a

commercial environment. If this unit is operated in a residential area, it may cause some

interference and under these circumstances the user would be required to take, at his own

expense, whatever measures are necessary to eliminate the interference.

(FCC = Federal Communications Commission in the U.S.A.)

1-3-2. Compliance with EMC Directives

This device features radio interference suppression and safety regulation in

compliance with the following Council Directives

Council directive 89/336/EEC EN61326 EMC directive

Council directive 73/23/EEC EN60950 Safety of Information Technology Equipment

The CE mark is an official mandatory European marking.

Please note that any electronic product must comply with local laws and

regulations when sold or used anywhere outside Europe.

Contents

Main MC-10K MC-30K This Manual and Marks WARNING CAUTION Contents Page 1. Introduction 1-1. About This Manual 1-2. Features 1-3. Compliance 1-3-1. Compliance with FCC Rules 1-3-2. Compliance with EMC Directives 2. Unpacking And Installing The Balance 2-1. Auto-centering Pan (AX-MC10K/30KPAN) Installation Procedure 2-2. Installing the Balance 3. Precautions 3-1. Before Use 3-2. During Use 3-3. After Use 3-4. Power Supply 4. Display Symbols And Key Operation Key Operations Display 5. Weighing Units Page 6. Weighing 6-1. Selecting a Weighing Unit (Mode) 6-2. Basic Weighing 6-2-1. For More Stable Weighing 6-2-2. When Using as a Mass Comparator 6-2-3. When Building into a System 7. Weighing Speed Adjustment / Self Check Function 7-1. Weighing Speed Adjustment end 0.000 0.000 7-2. Self Check Function with Response Adjustment CH . . . . CH 0.000 8. Calibration 8-1. Calibration Group Terms Caution Caution on using an external weight 8-2. Automatic Self Calibration Automatic self calibration due to changes in temperature Caution 8-3. One-Touch Calibration Calibration using the internal mass About the internal mass 8-4. Calibration Using an External Weight 0.000 2000.123 2000.120 2000.000 8-5. Calibration Test Using an External Weight 0.000 2000.123 2000.120 2000.000 8-6. Correcting the Internal Mass Value p5 a-01111 1 a-1 0.00 id 9. Function Switch And Initialization 9-1. Permit or Inhibit Automatic self calibration Function table Calibration using the internal mass (One-touch calibration) 9-2. Initializing the Balance Clr Clr go Clr no end 0.000 10. Function Table 10-1. Structure and Sequence of the Function Table Example 10-2. Display and Operation Keys 10-3. Details of the Function Table Page Page Page 10-4. Description of the Class "Environment, Display" Condition ( Cond ) Stability band width ( 5t-b ) Zero upon power-on ( p-tr ) Span calibration ( 5pn ) 10-5. Description of the Item "Data Output Mode" Key mode Auto print modes A and B Stream mode Interval memory mode 10-6. Description of the Item "Data Format" Stable header (Counting mode) A&D standard format 5if type 0 DP (Dump print) format 5if type 1 Unit DataHeader Ter min at or Stable header Unstable header Overload header KF format 5if type 2 MT format 5if type 3 Data Term inato r ID number Data number Date Time Weighing data NU (numerical) format 5if type 4 10-6-1. Description of the Data Format Added to the Weighing Data ID number dout 5-id 1 Data number Termi nat or Data number dout d-no 1 Date dout 5-td 2 or 3 10-7. Data Format Examples Stable Unstable Overload Unit 11. ID Number And GLP Report 11-1. Setting the ID Number 11-2. GLP Report Calibration report using the internal mass Calibration report using an external weight Calibration test report using an external weight Title block and end block Operation 12. Standard Input And Output Interface 12-1. RS-232C and External Contact Input D-Sub 25 pin numbers D-Sub 25 pin assignments RS-232C RS-232C Terminals External contact input Option 12-2. Connection to Peripheral Equipment 12-2-1. Connection to the AD-8121B Printer 12-2-2. Connection to a Computer and the Use of WinCT Using Windows Communication Tools Software (WinCT) RsCom RsKey Using the WinCT software, the balance can do the following: 13. Commands 13-1. Command List 13-2. Acknowledge Code and Error Codes 13-3. Control Using CTS and RTS Ct5 0 Ct5 1 13-4. Settings Related to RS-232C Command received Command completed 14. Extended Function 14-1. 14-1-2. Filter Depending on Differences in the Amount to Deliver Powdery and Liquid Material 15. Maintenance 15-1. Treatment of the Balance 16. Troubleshooting 16-1. Checking the Balance Performance and Environment Checking that the balance performs properly Checking that the operating environment or weighing method is proper Operating environment Weighing method 16-2. Error Codes Page 16-3. Other Display 16-4. Asking for Repair 17. Specifications 17-1. External Dimensions 17-2. Options and Peripheral Instruments AX-MC10K/30KPAN Auto-centering Pan AD-8922A Remote controller AD-8121B Printer Page 18. Terms/Index 18-1. Terms Page 18-2. Index