Manuals
/
Adcom
/
Home Audio
/
Stereo Amplifier
Adcom
GTP-760 owner manual This page has been interntionally left blank
Models:
GTP-760
1
43
44
44
Download
44 pages
11.65 Kb
37
38
39
40
41
42
43
44
<
>
Troubleshooting
Specs
Install
Maintenance
Programming “Preset” Stations
3.0INITIAL SETUP
Using Preprogrammed Commands
Delay
Signal to Noise Ratio Ref. to
34Tuning Up/Down
Page 43
Image 43
This page has been interntionally left blank.
42
Page 42
Page 44
Page 43
Image 43
Page 42
Page 44
Contents
Digital Processing Tuner / Preamplifier
GTP-760
Page
Explanation of Graphic Symbols
SAFETY NOTIFICATION PAGE
ADCOM PROTECTION PLAN USA ONLY
A NOTE FROM ADCOM
CONCEALED SHIPPING DAMAGE
Table of Contents
2.2Connecting Source Components to the GTP-760
3.0 INITIAL SETUP
2.0 INSTALLING/CONNECTING THE GTP-760
2.1Physical Placement
1.1Front Panel Controls
1.0PRODUCT FEATURES
Page
LEFT CHANNEL ANALOG AUDIO inputs
YELLOW centers
DIGITAL AUDIO inputs
CENTER CHANNEL and SUBWOOFER
Composite or S-Video?
AC power cord and AC fuse holder
Digital 1 RF Demodulator switch
Video Processor On/Off switch
Remote control connections
19 Digital Audio/Standard Composite Video Inputs
Video to the appropriate “dig.2 in” jack
VCR Inputs and Outputs
2112 Volt Trigger Output
Room 2 Outputs
Video Aux Input
Video Processor Inputs and Outputs
Standard Composite Video Monitor Outputs
Tape Inputs and Outputs
CD Inputs
23S-VideoInputs and Outputs
25Remote Control Connections
24Video Processor On/Off Switch
26 Preamplifier Outputs
27 5.1 Channel Inputs
AC Power Cord Receptacle export models
29 AC Convenience Outlets 115VAC models
1.3The Remote Control
30Source selectors main DVD
34 33 41 39 44 45 46 43 47 51
32Input Selectors tape, LD
31Power
33Volume Up/Down
34Tuning Up/Down
44FM/AM
40Down arrow/Stop
41Select/Play
43Shift
Center Down
Rear Up
Rear Down
Center Up
VOLUME +
POWER
TUNING +
TUNING
FM/AM
PROGRAMMING YOUR ADCOM GTP-760REMOTE CONTROLLER
Using Preprogrammed Commands
SHIFT
Programming Your Own Commands
Macro Commands
Deleting clearing Individual Programmed Commands
Deleting Macro Initiator Buttons
2.0INSTALLING/CONNECTING THE GTP-760
2.1Placement
Programming Macro Initiator Buttons
3.1The On Screen Display
3.0INITIAL SETUP
3.2CHANNEL DELAYS
What this section is all about
3.3SPEAKER SIZE
The speaker size menu allows you to describe the size and number of speakers in your system to the GTP-760.The descriptive words LARGE and SMALL that appear in the MAIN field mean the following
By Ear
3.4CHANNEL BALANCE
Sound Meter
3.5 INPUT SETTINGS
4.1Operating Mode Selection
4.0BASIC OPERATION
not active in this mode
The GTP-760’soperating modes are
4.2 The Tuner Selecting stations
Programming “Preset” Stations
Operating “Room 2” From the Front Panel
Listening to “Preset” Stations
Setting “Room 2” Playback Volume
4.3Room 2 Operation Introduction
Operating Room 2 From “Room 2”
5.0 TROUBLE SHOOTING
Page
CARING FORYOUR GTP-760
6.0CARE, MAINTENANCE, and SERVICE
SERVICING
Preamplifier Section
7.0 SPECIFICATIONS GTP-760
Signal to Noise Ratio Ref. to
Power available in 230V on special order
This page has been interntionally left blank
c2000 by ADCOM. All rights reserved
10 Timber Lane Marlboro, NJ Tel 732 Fax