Manuals / Brands / Computer Equipment / Computer Hardware / Advantech / Computer Equipment / Computer Hardware

Advantech PCM-9587 2.12 Front Panel Connector (CN22), 2.13 Power connectors (CN25,CN5), 2.14 ATX power ON/OFF switch con. pin 11-12 of CN22

1 82

Download 82 pages, 3.36 Mb

13 PCM-9587 User Manual

Chapter 2 Installation

2.12 Front Panel Connector (CN22)

Next, you may want to install external switches to monitor and control the PCM-9587.

These features are optional: install them only if you need them. The Front Panel con-

nector (CN22) is a 14-pin male, dual in-line header. It provides connections for a hard

disk access indicator, LAN Act., LAN Link, hardware reset, ATX power ON/OFF

switch connector, and power on indicator.

2.12.1 Power & HDD LED (pin 1-4 of CN22)

The HDD LED indicator for hard disk access is an active low signal (24 mA sink rate).

Power supply activity LED indicator.

2.12.2 Reset switch (pin 13-14 of CN22)

If you install a reset switch, it should be an open single pole switch. Momentarily

pressing the switch will activate a reset. The switch should be rated for 10 mA, 5 V.

2.13 Power connectors (CN25,CN5)

2.13.1 ATX power connector, +5V (CN5)

Supplies main power to the PCM-9587 (+5V) and to devices that require it.

2.13.2 CPU Fan power supply connector (CN25)

Provides power supply +12V to CPU cooling fan, and fan speed detects signal input.

2.14 ATX power ON/OFF switch con. pin 11-12 of CN22

2.14.1 ATX feature (CN5) & soft power switch (CN22)

The PCM-9587 can support an advanced soft power switch function, if an ATX power

supply is used. To enable the soft power switch function connect the power on/off

button to CN22. (A momentary type of button should be used.)

Note! Make sure that the ATX power supply can take at least a 10 mA load on

the 5 V standby lead (5VSB). If not, you may have difficulty powering on

your system.

Contents

Main Copyright Acknowledgements Packing List Order Information Optional accessories Declaration of Conformity Technical Support and Assistance Contents Chapter 1 General Information ............................1 Chapter 2 Installation............................................5 Chapter 3 Software Configuration .................... 19 Chapter 4 Award BIOS Setup ............................ 21 Chapter 5 PCI Graphic ....................................... 29 Chapter 6 Audio Setup .......................................35 Chapter 7 LAN Configuration.............................39 Appendix B Pin Assignments ...............................51 Appendix C System Assignments........................ 65 Appendix D Optional Extras for the PCM-9587... 69 Appendix E Mechanical Drawings ....................... 71 Chapter 1 1.1 Introduction 1.2 Features 1.3 Specifications Chapter 1 General Information Page Chapter 2 2.1 Jumpers 2.1.1 Jumpers setting drawing Table 2.1: Jumpers Table 2.2: J1: LCD Voltage Select Table 2.3: J2: PC104+ VIO Select Page 2.2 Connectors Table 2.6: Connectors Page 2.4 Setting Jumpers 2.5 Clear CMOS (J3) 2.6 Installing DIMMs 2.7 IDE, CDROM hard drive connector (CN15) 2.7.1 Connecting the hard drive 2.8 Solid State Disk 2.8.1 CompactFlash (CN30) 2.9 Floppy drive connector (CN14) 2.9.1 Connecting the floppy drive 2.10 Parallel port connector (CN16) 2.11 Keyboard and PS/2 mouse connector (CN27) 2.12 Front Panel Connector (CN22) 2.13 Power connectors (CN25,CN5) 2.14 ATX power ON/OFF switch con. pin 11-12 of CN22 2.15 Audio AC'97 Link interfaces (CN4) 2.15.1 Audio connector(CN4) 2.15.2 CD audio-in connector (CN3) 2.16 COM port connector (CN21) 2.17 VGA/LVDS interface connections (CN7, CN8,CN9) 2.18 TV-out interface (CN2) (TV out optional by request) 2.19 Ethernet configuration (CN11) 2.19.1 100Base-T connector (CN11) 2.19.2 Network boot Table 2.7: CN9: DVI connector 2.20 USB connectors (CN18,CN20) 2.21 LCD Backlight connector (CN1) 2.22 SATA Connector (CN23, CN24) 2.23 DIO connector (CN19) 2.24 -12V and -5V connector (CN6) 2.26 System FAN connector (CN13) Table 2.10: CN13: System FAN connector Page Chapter 3 Configuration 3.1 Introduction 3.2 Connections to Standard LCDs 3.2.1 LG LM150X06 (1024x768(16 colors) LVDS LCD) Table 3.1: Connections to LCD/ Flat Panel (CN8) Page 4.1 System test and initialization 4.1.1 System configuration verification 4.2 Award BIOS setup 4.2.1 Entering setup Page Page Page Page 4.2.10 Load Optimized Defaults 4.2.11 Set Password 4.3 Save & Exit Setup 4.3.1 Exit Without Saving Page 5.1 Introduction 5.1.1 Chipset 5.1.2 Display memory 5.1.3 Display types 5.1.4 Dual/Simultaneous Display Page 5.2 Installation of the PCI Graphic driver 5.2.1 Installation for Windows 2000/XP Page Page Chapter 6 6.1 Introduction 6.2 Driver installation 6.2.1 Before you begin 6.2.2 Windows 2000/XP drivers Page Page Chapter 7 7.1 Introduction 7.2 Features 7.3 Installation of Ethernet Driver 7.3.1 Installation for Windows 2000 Page Page Page Page Page Page Appendix A A.1 Supported GPIO Register A.1.1 GPIO Registers A.1.2 GPIO Example program-1 Appendix A Programming the GPIO and Watchdog Timer A.2 Watchdog programming Page B.1 LCD Backlight Connector (CN1) B.2 TV Out Connector (CN2) (TV out optional by request) B.3 CD-IN Connector (CN3) Table B.1: LCD Backlight Connector (CN1) Table B.2: TV Out Connector (CN2) (TV out optional by request) B.4 Audio Output Connector (CN4) B.5 Power input Connector (CN5) B.6 -12V and -5V Connector (CN6) Table B.4: Audio Output Connector (CN4) Table B.5: Power input Connector (CN5) B.7 VGA Connector (CN7) B.8 LVDS Connector (CN8) Table B.7: VGA Connector (CN7) Table B.8: CN8 LVDS connector B.9 DVI Connector (CN9) B.10 Gigabit LAN Connector (CN10 Optional) B.11 10/100M LAN Connector (CN11) Table B.9: DVI Connector (CN9) Table B.10: Gigabit LAN Connector (CN10) B.12 Gigabit LAN LED Connector (CN12 Optional) B.13 System FAN Connector (CN13) B.14 Floppy Disk Drive Connector (CN14) Table B.12: Gigabit LAN LED Connector (CN12) Table B.13: System FAN Connector (CN13) Table B.14: Floppy Disk Drive Connector (CN14) B.15 Primary HDD Connector (CN15) B.16 Printer Port Connector (CN16) * low active Table B.15: Primary HDD Connector (CN15) Table B.16: Printer Port Connector (CN16) B.17 USB Connector (CN18,20) B.18 DIO Connector (CN19) Table B.17: USB Connector (CN18,20) Table B.18: DIO Connector (CN19) B.19 COM Port Connector (CN21) Table B.19: COM Port Connector (CN21) B.20 Front Panel Connector (CN22) B.21 SATA Connector 1 (CN23) Table B.20: Front panel Connector (CN22) Table B.21: SATA Connector 1 (CN23) B.22 SATA Connector 2 (CN24) B.23 CPU FAN Connector (CN25) B.24 Extension SMBUS Connector (CN26) Table B.22: SATA Connector 2 (CN24) Table B.23: CPU FAN Connector (CN25) Page B.27 Mini PCI Connector(CN29) B.28 CompactFlash Card Connector (CN30) Table B.27: Mini PCI Connector (CN29) Table B.28: CompactFlash Card Connector (CN30) Page Appendix C C.1 System I/O Ports * PNP audio I/O map range from 220 ~ 250H (16 bytes) MPU-401 select from 300 ~ 330H (2 bytes) Table C.1: System I/O Ports Appendix C System Assignments C.2 1st MB memory map C.3 DMA channel assignments * Audio DMA select 1, 3, or 5 ** Parallel port DMA select 1 (LPT2) or 3 (LPT1) Table C.2: 1st MB memory map C.4 Interrupt assignments Table C.4: Interrupt assignments Page D.1 PCM-10586-6200E Cable kit for PCM-9587 Table D.1: PCM-10586-6200E wiring kit 9587 Page Page Page www.advantech.com