Akai RMD-V3104U CHAPTER 7. MVP MANUAL

140

MVP MANUAL

1. INTRODUCTION

The multi video processor (hereafter referred to as MVP below) is equipped with a serial interface conforming to

RS-232C standards which can be connected to computers.

This manual is required when connecting the MVP to the external computer and controlling adjustments and

performance.

This manual describes the methods of using the RS-232C interface, command protocols, and basic functions

and commands of the MVP.

CHAPTER 7. MVP MANUAL

Contents

Main Page Page Page Page Page Page Page Page Page Page Page Page CHAPTER 7. MVP MANUAL 1. INTRODUCTION 2. CONNECTION WITH MVP EXTERNAL COMPUTER 3. INSTRUCTIONS FOR USING A COMPUTER AS A TERMINAL <When the IBM-PC/AT is used> <With the PC-9800 series> <Example of a program GW-BASIC> <Communication mode settings in use of CCT98> 4. OPERATING MODES Page 5. MVP VIDEO OUTPUT MODES 6. ADJUSTMENT FUNCTIONS (1) MVP settings (2) NTSC input board setting (3) Variable scan board settings 7. PICTURE FRAME ADJUSTMENT PROCEDURES 1. Command reference (3) To set the system back to 4-screen magnification [@ command] NOTE) An input board must be added in order to display the image of the OPTION input. (Option) 2. Adjusting the picture frame (1) To perform fine adjustment of the picture frame [&G command] (2) To perform coarse adjustments of the picture frame [&P2, &Q2 commands] (3) To store the picture frame data [&W command] (4) To load the picture frame data [&L command] 3. To switch the image input [IFF command] RGB Personal computer 4. To indicate the current MVP state [SYS command] 5. To perform NTSC input board picture quality adjustment (1) To set the adjustment mode [AJYC command] (2) To exit the adjustment mode [AJN command] (3) Bright compensation [BRT command] (4) Color compensation [COL command] (5) Tint adjustment [TNT command] 6. Controls the panel switch function (1) To set the manual mode [MNL command] (2) To set the remote mode [RMT command] (3) To select composite video input [CIC command] (4) To select YC separation input [YIC command] (NOTE) With the RMD-V2550U, only standard speed input is possible. (8) Optional variable scan board adjustment mode settings [:A command] 8. DEMO PATTERN SETTINGS AND CAUTIONS 9. INSTALLING AND REMOVING BOARDS <Removal procedure> For your safety <Installation procedure> <Board layout> <Relationship between board insertion lanes and rear panel connectors> 10. RMD-V3020 COMMAND REFERENCE (1) Outline of the RMD-V3020 (2) VS board command rules 0. Symbols 1. Basic commands 2. Exceptional commands (3) Tracking adjustment [TRK command] (4) Contrast adjustment [CNT command] (5) R, G, B gain adjustment [RGN, GGN, BGN commands] (6) Brightness adjustment [BRT command] (7) B, R clamp adjustment [BLV, RLV commands] (8) Blanking window level adjustment [BLK command] (9) Horizontal, vertical direction screen display position adjustment [HPS, VPS commands] AA (10) Horizontal, vertical blanking window position adjustment [HWN, VWN commands] (11) Horizontal, vertical blanking window width adjustment [HWD, VWD commands] A A A A A A (12) Full dot number compensation [HFD command] (13) Freeze frame Y:ON N:OFF [FZY, FZN commands] (14) Vertical filter ON/OFF [DSY, DSN, DSX commands] (15) Vertical compression filter conversion rate input [LCV command] (16) Program ROM version display [VER command] (17) To indicate the current function setting [STS command] (18) To select preset model [M command] (19) Model fresh [F command] (20) Measurement data display [FRQ command] (21) Model table reference [TBL command] Note 1 Note 2 Note 4 Note 3 (22) Horizontal frequency input [HFQ command] Note 4 (23) Vertical frequency input [VFQ command] (24) Vertical full-line input [VLN command] (25) All reset [ARS command] 11. MODE 99 12. VS BOARD MODEL SELECTION 13. USING METHODS OF HFQ, VFQ, VLN 14. SELECTING THE SYNC SIGNAL