Alliance Laundry Systems 100, 135, 165, 18, 200, 33, 35, 40, 55, 75

Installation

9001000

Table 6 (continued)

Electrical Specifications

Voltage Designation Standard Electric Heat

Model

Code

Volta ge

Cycle

Phase

Wire

Full

Load

Amps

Circuit

Breaker

AWG

/mm2

Full Load

Amps

(Heating

Element

kW)

Circuit

Breaker

AWG

/mm2

165

N 440-480 50/60 3 3+PE 20 25 10/6.0 41 (9x3 kW) 63 8/10.0

52 (9x4 kW) 63 8/10.0

P 380-415 50/60 3 3+N+PE 20 25 10/6.0 50 (9x3 kW) 63 8/10.0

61 (9x4 kW) 80 6/16.0

Q 200-240 50/60 3 3+PE 32 40 8/10.0 76 (9x3 kW) 100 4/25.0

200

N 440-480 50/60 3 3+PE 19 25 10/6.0 42 (9x3 kW) 63 8/10.0

53 (9x4 kW) 63 8/10.0

P 380-415 50/60 3 3+N+PE 18 25 10/6.0 51 (9x3 kW) 63 8/10.0

62 (9x4 kW) 80 6/16.0

Q 200-240 50/60 3 3+PE 27 40 8/10.0 77 (9x3 kW) 100 4/25.0

Table 6

Contents

Main Installation Washer-Extractors Cabinet Freestanding Refer to Page 6 for Model Identification Keep These Instructions for Future Reference. Page Table of Contents Safety Information Explanation of Safety Messages Important Safety Instructions DANGER Page Safety Decals Operator Safety Introduction Model Identification Information in this manual is applicable to these models: Page Nameplate Location Replacement Parts Customer Service * Specifications and Dimensions Page Page Page 14 Figure 3 15 Figure 4 16 Figure 5 17 Figure 6 18 Figure 7 19 Figure 8 20 Figure 9 21 Figure 10 22 Figure 11 23 Figure 12 24 Figure 13 Installation Dimensional Clearances Table 1 Tabl e 1 shows recommended minimum clearances on all sides of the washer-extractor. Recommended Minimum Clearances Model 18253335405575100135165200 Machine Foundation 27 Mechanical Installation 18 MODEL Figure 14 28 Figure 15 25 POUND 29 Figure 16 33 MODEL 30 Figure 17 35 MODEL 31 Figure 18 40 MODEL 32 Figure 19 55 MODEL 33 Figure 20 75 MODEL 34 Figure 21 100 MODEL 35 Figure 22 135 MODEL 36 Figure 23 165 POUND 37 Figure 24 200 POUND 38 18, 25 and 35 Pound Capacity with A or M in the 8th position of the Model Number (e.g. *X18PVXA6) 18 MODEL Figure 25 39 Figure 26 25 MODEL 40 Figure 27 35 MODEL Mounting Bolt Installation (If Required) Removing the Transport Brackets 43 Figure 30 Figure 32 Figure 31 Drain Connection Page Water Connection Electrical Installation DANGER Page Page Electrical Connection Remote Liquid Supply Connection Chemical Injection Supply System Steam Requirements (Steam Heat Option Only) Supply Programming Table NOTE: The Supply button is button 6. Supply Relay Configuration (No Wiring) Primary 220 Volt Remote Liquid Supply Connection Primary 220 Volt Remote Liquid Supply Connection (Continued) Out-of-Balance Switch Automatic Lubricator Control Function Test (L1) (L2) (L3) MACHINE

Alliance Laundry Systems - page 51

Models: 100 135 165 18 200 33 35 40 55 75