Manuals / Brands / Laundry Appliance / Washer/Dryer / Alliance Laundry Systems / Laundry Appliance / Washer/Dryer

Alliance Laundry Systems CHM166C For machines equipped with a cardreader:, 11. Cycle is complete when display reads “:00”, If display flashes “SPEC” then “CYCL”, extra options such as

1 38

Download 38 pages, 1.21 Mb

Installation/Operation Supplement

7.For machines equipped with a cardreader: Insert card into cardreader and follow the instructions. Refer to Figure 13. DO NOT REMOVE CARD UNTIL DISPLAY ON CARDREADER READS “Remove Card”.

WASHINSERT

COIN/CARD

	CLOSE	NORMAL	PERM	DELICATE	SPECIAL
RINSE			PRESS	DELICATES	* WASH
	DOOR
	ADD	HOT	WARM	COLD	START
SPIN	BLEACH			COLD

B149R

Figure 13

8. Add detergent to container 1 and softener to container 3. Press the START key. Refer to Figure 14.

13

							CIAL
						*	SWPEASH
*						*
*					DELICA	START
	SPECIAL				TES
	SPECIAL			PPREERSS	COLD
	WASH			M
	WASH	NORM	AL	RM
		NORM		WA
		HOT

START

B155R

2

B155R

1Detergent

2Bleach

3Softener

Figure 14

NOTE: If a higher-priced cycle is selected, after the full price has been satisfied for current cycle, display will show additional price required and the INSERT COIN/CARD light will flash. Insert coins/ card to satisfy price for special cycle. If price is not satisfied, the previous cycle selected will begin after one minute.

9.If display flashes “SPEC” then “CYCL”, extra options such as high-speed extract or extra rinse are available. If desired, insert coins/card to meet additional price shown on display. If not desired, wait 30 seconds for earlier cycle selection to continue.

10.Add bleach to container 2 when ADD BLEACH light is lit. Refer to Figure 15.

1

3

*

2

WASHINSERT

COIN/CARD

RINSE	CLOSE
	DOOR
SPIN	ADD
	BLEACH

B156R

1Detergent

2Bleach

3Softener

Figure 15

11. Cycle is complete when display reads “:00”.

28

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232145 (EN)

Contents

Page Page Table of Contents Notes Safety Information Important Safety Instructions Page Specifications and Dimensions 2 Speed Models (Continued) Door Opening Information Power Consumption Drive Train Information Cylinder Speeds Balance Detection Direct Steam Heating (Optional) Electrical Heating (Optional) Gap Setting for Vibration Switch (Variable-Speedand Fixed-SpeedModels) Table 3 (Continued) Page For 18, 20, 25, 27, 30 and 35 Pound Capacity Machines For 40 and 50 Pound Capacity Variable-Speed and Fixed-SpeedMachines For 60 Pound Capacity Variable-Speedand Fixed-SpeedMachines For 80 Pound Capacity Machines For 125 Pound Capacity Machines Dimensional Clearances Dimensions Machine Capacity Dimensions Dimensions 125 Model Electrical Specifications Page Page Page Page Operation Symbol 30C Description Instructions for EDC Control For machines equipped with a cardreader: If display flashes “SPEC” then “CYCL”, extra options such as 10.Add bleach to container 2 when ADD BLEACH light is lit. Refer to Figure 11. Cycle is complete when display reads “:00” Instructions for Mechanical Timer 5. Select wash cycle. Refer to Figure a.Add detergent to container b.Add softener to container For coin models: For non-coinmodels: Press the Start button. Refer to Figure Instructions for S, P and V Series Microcomputers 5.Add liquid and/or powder supplies to supply dispenser. Refer to Figure 6.Press the Up and Down keys to select wash cycle. Refer to Figure 8.For non-coinmodels: Press the Start key. Refer to Figure When applicable NOTE: To stop a cycle at any time, press the Stop key. Non-coinmodels only Instructions for B Series Microcomputer Page Instructions for A Series