Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis C613-02013-00 Configuration Scripts, Saving Configuration Entered with the GUI

Models: C613-02013-00

1 66

Download 66 pages 27.56 Kb

Page 19

Operating the Switch						19
Figure 4: Example of output from the SHOW SYSTEM command

Switch System Status					Time 14:29:17 Date 12-Sep-2000.
Board	ID	Bay Board Name			Rev	Serial number
--------------------------------------------------------------------------
Base	86		AT-RP24 Rapier 24		P2-1	49867449
--------------------------------------------------------------------------
Memory -	DRAM	:	32768 kB	FLASH : 6144 kB
--------------------------------------------------------------------------
SysDescription
CentreCOM AT-RP24			Rapier 24 version 2.1.0-00 04-Sep-2000
SysContact
SysLocation
SysName
SysUpTime
30262 ( 00:05:02 )
Software Version: 2.1.0-00 04-Sep-2000
Release Version		: 2.1.0-00 04-Sep-2000
Release built		: Sep 12 2000 at 14:28:59
Patch Installed		: NONE
Territory		: usa
Help File		: help.hlp
Main PSU		: On		Main Fan	: On
RPS Monitor		: On		RPS Connected	: Yes
RPS PSU		: On
Boot configuration file: vts.cfg (exists)
Current configuration: vts.cfg
Security Mode		: Disabled
Warning (248283): No patches found.

Configuration Scripts

At boot the switch executes the commands in the boot script to configure the switch. A boot script is a sequence of standard commands that the switch executes at start-up. The default boot script is called boot.cfg, but an alternative script file can be defined as the boot script using the command:

SET CONFIG=filename

A configuration file is a script made up of the same commands as are used in the CLI. It can be edited manually using the switch’s built in editor (“Editor” on page 20), or uploaded to a PC and edited using any text editor using the UPLOAD command (Chapter 1, Operation in the Rapier Switch Software Reference.

Saving Configuration Entered with the GUI

Configuration changes applied using the GUI automatically update the configuration script specified in the SET CONFIG command.

Rapier Switch Software Release 2.2.1 C613-02013-00 Rev A

Image 19

Allied Telesis C613-02013-00 manual Configuration Scripts, Saving Configuration Entered with the GUI

Contents

USER GUIDE RAPIER SWITCHAll trademarks are the property of their respective owners Rapier Switch User Guide Document Number C613-02013-00 REV AIntroduction ContentsCHAPTER 3 Operating the Switch CHAPTER 4 Layer 2 SwitchingDocumentation Roadmap CHAPTER 5 Layer 3 SwitchingIntroduction Why Read This User Guide?Chapter Technical support Where To Find More InformationSwitching Features What Can the Rapier Switch Do?Routing Features See “Enable AT-RPFL3Upgrade Feature Licence” on page Advanced Feature Licence AT-RPFL3UpgradeOptional Features Chapter Simple SwitchingCommand Line Interface Getting StartedEntering Commands Giving the Switch an IP AddressLogging In Enabling the GUI Enable AT-RPFL3Upgrade Feature LicenceStarting the GUI Graphical User InterfaceConfiguring Using help modeNavigating Exiting TroubleshootingChanging your password MonitoringChapter Operating the SwitchUser Privileges File SubsystemFigure 3 Example output from the SHOW FILE command Online CLI HelpSaving Configuration Entered with the GUI Configuration ScriptsEditor Saving Configuration Entered with the CLIInstall Information Figure 6 Example output from the SHOW INSTALL command OFFICER privilegeReleases and Patches into the Switch To install a compressed release Example Install Software Upgrade for Rapier SwitchSoftware Reference SNMP and MIBswhere interface is the name of an interface, such as vlan11 Chapter Layer 2 SwitchingSwitch Ports Enabling and Disabling Switch PortsParameter To display information about switch ports, use the commandFigure 8 Example output from the SHOW SWITCH PORT command Table 3 Parameters in the output of the SHOW SWITCH PORT commandParameter Autonegotiation of Port Speed and Duplex ModeLayer 2 Switching Table 3 Parameters in the output of the SHOW SWITCH PORT commandPreference Port Trunking10/100 Ethernet switch ports Table 4 Autonegotiation preferences for Ethernet portsTo display information about trunks on the switch, use the command Packet Storm Protection SET SWITCH PORT=port-listALL MIRROR=NONERXTXBOTH Port MirroringSHOW SWITCH PORT=port-list SET SWITCH MIRROR=NONEportPort security Virtual LANs A VLAN can contain a mixture of VLAN tagged and untagged ports Creating VLANs Without VLAN Tags Static and dynamic VLANsMarketing VLAN Switch Training VLAN Parameter Layer 2 SwitchingFigure 10 Example output from the SHOW VLAN command Table 5 Parameters displayed in the output of the SHOW VLAN commandVLAN Tagging VLANs to be used with VLAN tags are created and destroyed in the same way as VLANs with only untagged ports, by using the commands Figure 11 Tagged VLANs Summary of VLAN Tagging RulesGeneric VLAN Registration Protocol GVRP Layer 2 Switching ProcessThe Ingress Rules The Learning Process The Forwarding Process Layer 2 Filtering because it has been added with the LEARN parameter of the The Egress RulesSET SWITCH PORT command, or has been dynamically learned This parameter is either “static” indicating the filter is a staticFigure 13 Example output from the SHOW SWITCH QOS command Quality of ServicePriority level Spanning Tree Port States Spanning Tree Protocol STPADD STP=stpname VLAN=vlanname2..4094 Configuring STPENABLE STP=stpnameALL DISABLE STP=stpnameALL SHOW STP PORT=port-listTo change the STP priority value, use the command Meaning Figure 14 Example output from the SHOW STP commandTable 10 Parameters in the output of the SHOW STP command ParameterForward Delay Parameter To restore default port pathcost and priority, use the commandTo display STP port information, use the command Figure 15 Example output from the SHOW STP PORT commandParameter Layer 2 SwitchingFigure 16 Example output from the SHOW STP COUNTER command Table 12 Parameters in the output of the SHOW STP COUNTER commandIGMP Snooping Interfaces to Layer 3 ProtocolsIGMP is enabled and disabled using the commands Triggers The port number of the port which has just come up EventDescription ParametersPage Internet Protocol IP Layer 3 SwitchingChapter IP Multicasting PIM Sparse ModeRouting Information Protocol RIP Novell IPX SHOW APPLE PORT AppleTalkResource Reservation Protocol RSVP ADD APPLE PORT INTERFACE=vlan11Figure 22 Example output from the SHOW RSVP INTERFACE command The commanddisplays information about the interfaces enabled for RSVP Figure Layer 3 Switching