Manuals / Allied Telesis / Computer Equipment / Switch

Allied Telesis C613-02013-00 manual where interface is the name of an interface, such as vlan11

Models: C613-02013-00

1 66

Download 66 pages 27.56 Kb

Page 26

26	Rapier Switch User Guide

Authentication failure traps and link state traps can be enabled using the commands:

ENABLE SNMP AUTHENTICATE_TRAP

ENABLE INTERFACE=interface LINKTRAP

where interface is the name of an interface, such as vlan11.

The command:
SHOW SNMP
displays the current state and configuration of the SNMP agent (Figure 7 on
page 26).
Figure 7: Example output from the SHOW SNMP command.

SNMP configuration:
Status	Enabled
Authentication failure traps .... Enabled
Community	public
Access	read-only
Status	Enabled
Traps	Enabled
Open access	Yes
Community	Administration
Access	read-write
Status	Disabled
Traps	Disabled
Open access	No
SNMP counters:
inPkts	0	outPkts	0
inBadVersions	0	outTooBigs	0
inBadCommunityNames	0	outNoSuchNames	0
inBadCommunityUses	0	outBadValues	0
inASNParseErrs	0	outGenErrs	0
inTooBigs	0	outGetRequests	0
inNoSuchNames	0	outGetNexts	0
inBadValues	0	outSetRequests	0
inReadOnlys	0	outGetResponses	0
inGenErrs	0	outTraps	0
inTotalReqVars	0
inTotalSetVars	0
inGetRequests	0
inGetNexts	0
inSetRequests	0
inGetResponses	0
inTraps	0

The following MIBs are supported:

■MIB II (RFC 1213)

■Ethernet MIB (RFC 1643)

■Trap MIB (RFC 1215)

■RMON Groups 1, 2, 3, and 9 (RFC 1757)

■AR Router portion of the ATI/ATKK Enterprise MIB

■Portions of the Extended Interface MIB (RFC 1573)

Rapier Switch Software Release 2.2.1 C613-02013-00 Rev A

Image 26

Allied Telesis C613-02013-00 manual where interface is the name of an interface, such as vlan11

Contents

RAPIER SWITCH USER GUIDERapier Switch User Guide Document Number C613-02013-00 REV A All trademarks are the property of their respective ownersCHAPTER 4 Layer 2 Switching ContentsCHAPTER 3 Operating the Switch IntroductionCHAPTER 5 Layer 3 Switching Documentation RoadmapChapter Why Read This User Guide?Introduction Where To Find More Information Technical supportWhat Can the Rapier Switch Do? Switching FeaturesRouting Features Advanced Feature Licence AT-RPFL3Upgrade See “Enable AT-RPFL3Upgrade Feature Licence” on pageOptional Features Getting Started Simple SwitchingCommand Line Interface ChapterLogging In Giving the Switch an IP AddressEntering Commands Enable AT-RPFL3Upgrade Feature Licence Enabling the GUIGraphical User Interface Starting the GUINavigating Using help modeConfiguring Monitoring TroubleshootingChanging your password ExitingFile Subsystem Operating the SwitchUser Privileges ChapterOnline CLI Help Figure 3 Example output from the SHOW FILE commandConfiguration Scripts Saving Configuration Entered with the GUISaving Configuration Entered with the CLI EditorInstall Information OFFICER privilege Figure 6 Example output from the SHOW INSTALL commandReleases and Patches into the Switch Example Install Software Upgrade for Rapier Switch To install a compressed releaseSNMP and MIBs Software Referencewhere interface is the name of an interface, such as vlan11 Enabling and Disabling Switch Ports Layer 2 SwitchingSwitch Ports ChapterTable 3 Parameters in the output of the SHOW SWITCH PORT command To display information about switch ports, use the commandFigure 8 Example output from the SHOW SWITCH PORT command ParameterTable 3 Parameters in the output of the SHOW SWITCH PORT command Autonegotiation of Port Speed and Duplex ModeLayer 2 Switching ParameterTable 4 Autonegotiation preferences for Ethernet ports Port Trunking10/100 Ethernet switch ports PreferenceTo display information about trunks on the switch, use the command Packet Storm Protection SET SWITCH MIRROR=NONEport Port MirroringSHOW SWITCH PORT=port-list SET SWITCH PORT=port-listALL MIRROR=NONERXTXBOTHPort security Virtual LANs A VLAN can contain a mixture of VLAN tagged and untagged ports Static and dynamic VLANs Creating VLANs Without VLAN TagsMarketing VLAN Switch Training VLAN Table 5 Parameters displayed in the output of the SHOW VLAN command Layer 2 SwitchingFigure 10 Example output from the SHOW VLAN command ParameterVLAN Tagging VLANs to be used with VLAN tags are created and destroyed in the same way as VLANs with only untagged ports, by using the commands Summary of VLAN Tagging Rules Figure 11 Tagged VLANsThe Ingress Rules Layer 2 Switching ProcessGeneric VLAN Registration Protocol GVRP The Learning Process The Forwarding Process Layer 2 Filtering This parameter is either “static” indicating the filter is a static The Egress RulesSET SWITCH PORT command, or has been dynamically learned because it has been added with the LEARN parameter of thePriority level Quality of ServiceFigure 13 Example output from the SHOW SWITCH QOS command Spanning Tree Protocol STP Spanning Tree Port StatesSHOW STP PORT=port-list Configuring STPENABLE STP=stpnameALL DISABLE STP=stpnameALL ADD STP=stpname VLAN=vlanname2..4094To change the STP priority value, use the command Parameter Figure 14 Example output from the SHOW STP commandTable 10 Parameters in the output of the SHOW STP command MeaningForward Delay Figure 15 Example output from the SHOW STP PORT command To restore default port pathcost and priority, use the commandTo display STP port information, use the command ParameterTable 12 Parameters in the output of the SHOW STP COUNTER command Layer 2 SwitchingFigure 16 Example output from the SHOW STP COUNTER command ParameterInterfaces to Layer 3 Protocols IGMP SnoopingIGMP is enabled and disabled using the commands Triggers Parameters EventDescription The port number of the port which has just come upPage Chapter Layer 3 SwitchingInternet Protocol IP Routing Information Protocol RIP PIM Sparse ModeIP Multicasting Novell IPX ADD APPLE PORT INTERFACE=vlan11 AppleTalkResource Reservation Protocol RSVP SHOW APPLE PORTLayer 3 Switching The commanddisplays information about the interfaces enabled for RSVP Figure Figure 22 Example output from the SHOW RSVP INTERFACE command