68-09359Z38-A_F.book Page 24 Tuesday, September 4, 2007 4:15 PM

Installation and Connections

Before installing or connecting the unit, please read the following and pages 3 to 5 of this manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, shift lever, brake pedals, etc. can be extremely hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number or the engraved serial number is located on the bottom of the unit.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.

Precautions

•Be sure to disconnect the cable from the (–) battery post before installing your CDE-9874E/CDE-9872E. This will reduce any chance of damage to the unit in case of a short-circuit.

•Be sure to connect the colour coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle’s electrical system.

•When making connections to the vehicle’s electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the CDE-9874E/CDE-9872E to the fuse box, make sure the fuse for the intended circuit of the CDE-9874E/CDE-9872E has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your Alpine dealer.

•The CDE-9874E/CDE-9872E uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized Alpine dealer for assistance.

•Be sure to connect the speaker (–) leads to the speaker (–) terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.

SERIAL NUMBER:

INSTALLATION DATE:

INSTALLATION TECHNICIAN:

PLACE OF PURCHASE:

24-EN

01GB05CDE9874E.fm

ALPINE CDE-9874E 68-09359Z38-A (EN)

Page 25 Page 27
Page 26
Image 26
Alpine CDE-9872E, CDE-9874E owner manual Installation and Connections, 24-EN
Page 25 Page 27

CDE-9872E, CDE-9874E specifications

The Alpine CDE-9874E and CDE-9872E are two standout models in the world of car audio systems, designed to enhance your driving experience with high-quality sound and advanced technological features. Both models showcase Alpine's commitment to superior audio performance, ease of use, and connectivity options.

The Alpine CDE-9874E is equipped with a powerful 4-channel amplifier, delivering 50 watts RMS per channel, ensuring that every note and beat comes through with crystal clarity. It supports a wide range of audio formats, including MP3, WMA, and AAC, which makes it versatile for users who enjoy digital music. The CDE-9874E also includes a built-in CD player, as well as a USB port for direct connection to your smartphone or MP3 player. A notable feature is the Bluetooth connectivity, allowing seamless pairing with smartphones for hands-free calls and audio streaming.

Another remarkable characteristic of the CDE-9874E is its excellent sound customization capabilities. Featuring a 3-band parametric EQ, users can tailor the audio output to their liking, while the Time Correction and Digital Signal Processing (DSP) technologies offer professional-grade sound tuning. The display is user-friendly, with a bright and clear interface that makes navigating between different audio sources and settings a breeze.

On the other hand, the CDE-9872E shares many similarities but includes a few distinct features that set it apart. While lacking Bluetooth, the CDE-9872E still provides a USB connection and supports various digital audio files, appealing to users who prefer wired connections. This model is also optimized for audio performance, with a built-in amplifier that delivers impressive sound quality.

Both models boast a robust build quality, designed to withstand the bumps of the road while maintaining optimal performance. The intuitive user interface allows for quick adjustments while driving, ensuring that your focus remains on the road ahead.

In summary, whether you choose the Alpine CDE-9874E with its advanced Bluetooth capabilities and extensive sound customization options or the CDE-9872E with its solid performance and straightforward design, both models promise to elevate your in-car audio experience to new heights. Enjoy the perfect blend of convenience, performance, and style with these exceptional car stereos.
Top Page Image Contents