MobileHub™ Link Operation(Optional)
SOURCE/ |
|
|
|
| BAND/ |
|
|
|
|
|
|
|
|
|
| ||||||||||||||
POWER |
| 8 SEARCH | |||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
g MENU fRotary | 9 F Preset buttons |
encoder | (1 through 6) |
About MobileHub™ Link
Connect a separately sold junction box and a portable telephone (available from Nokia) to control the incoming and outgoing calls of the portable telephone.
Caution
Even with
For the sake of safety, only incoming calls and
•If a portable telephone is connected, its address book, incoming and outgoing history are downloaded to the junction box.
•Please refer to the instruction manual of the junction box.
Telephone Mode ON/OFF
Press and hold BAND/TEL. for at least 2 seconds to turn on the Telephone mode.
To turn off, press BAND/TEL.
See relevant pages for each item.
•“NO PHONE” is displayed for about 2 seconds, if a portable telephone is not connected, before entering the telephone mode. Then the mode returns to the original source mode
•When the portable telephone is taken off the junction box during an incoming or outgoing call, or during a
•When there is an incoming call while the power of
•Even if the power of the portable telephone is off, when
•Even if the ACC power of the vehicle is turned off (even if the engine is stopped) during a
•If there is an incoming call during operation (except an outgoing call or talking), operation mode will end and switch to the incoming or talking mode.
•An outgoing call from a portable telephone is also possible. However, you cannot perform different operations at the same time from a portable telephone and
•With a junction box connected outgoing, incoming, and sending history will also be recorded in the portable telephone.
•While telephoning, defeat is set to ON. When the call has finished, the unit returns to your previous setting.
•The telephone volume can be adjusted on the
•While telephoning or receiving incoming calls, press TITLE 
to show the Network Operator display for 5 seconds.
Incoming Calls
1 Press :/J to receive an incoming call.
2 Press BAND/TEL. to finish a call.
Telephone mode will end and return to the original source mode.
•When the Automatic Calling mode is on, you can talk after 3 seconds of receiving the incoming call. (See “Setting the Automatic Calling” described below.)
Setting the Automatic Calling
The incoming call can be switched to Automatic Calling or Manual Calling.
1 Press MENU to select the SETUP mode.
2 Select the TELEPHONE (TEL for
3 Turn the Rotary encoder to change to AUTO or MANUAL (MANU for
4 Press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will return to normal mode.
•Press BAND/TEL. during an incoming call to disconnect it.
•The initial setting of the factory is MANUAL.
