8. | RDRO – (RED L.E.D.) | This L.E.D. will indicate the status of the Rear Doors. If the doors are open, |
|
| then the L.E.D. is ON. |
9. | FAN – (RED L.E.D.) | This L.E.D. will indicate the status of the Blower Fan. If the fan is on, then the |
|
| L.E.D. is ON. |
10. | RBHL – (RED L.E.D.) | This L.E.D. will indicate the status of the Rear Burner |
|
| disk is closed (Temperature below 330º F [166º C]), then the L.E.D. is ON. |
11. | R_SS – (RED L.E.D.) | This L.E.D. will indicate the status of the Rear Sail Switch. If the switch is |
|
| closed, then the L.E.D. is ON. |
12. | FBHL – (RED L.E.D.) | This L.E.D. will indicate the status of the Front Burner |
|
| disk is closed (Temperature below 330º F [166º C]), then the L.E.D. is ON. |
13. | F_SS – (RED L.E.D.) | This L.E.D. will indicate the status of the Front Sail Switch. If the switch is |
|
| closed, then the L.E.D. is ON. |
14. | EXHL – (RED L.E.D.) | This L.E.D. will indicate the status of the Exhaust |
|
| closed (Temperature below 225º F [107º C]), then the L.E.D. is ON. |
15. | DRY – (RED L.E.D.) | This L.E.D. will indicate the status of the Programmable Logic Controller (PLC). |
|
| If the mechanical functions of the dryer have been set to the DRY position, the |
|
| PLC will send a signal to the Phase 7 board. This signal will indicate that ALL |
|
| the doors are closed and the dryer is level. When these conditions are met, then |
|
| the L.E.D. is ON. |
16. | LINT – (RED L.E.D.) | This L.E.D. will indicate the status of the Lint Drawer. If the drawer is closed, |
|
| then the L.E.D. is ON. |
17. | R_HE | Supply power for rear heat output (optional). |
18. | F_HE | Supply power for front heat output. |
19. | 24VM – (RED L.E.D.) | Control voltage at the spare inputs. |
20. | FVLV – (RED L.E.D.) | This L.E.D. will indicate the status of the Front Gas Valve. If the Front Gas |
|
| Valve is open (ON), then the L.E.D. is ON. |
21. | RVLV – (RED L.E.D.) | This L.E.D. will indicate the status of the Rear Gas Valve. If the Rear Gas |
|
| Valve is open (ON), then the L.E.D. is ON. |
22. | SPR1 – (RED L.E.D.) | This is for a spare input to be used with programmable outputs. |
23. | SPR2 – (RED L.E.D.) | This is for a spare input to be used with programmable outputs. |
24. | SPR3 – (RED L.E.D.) | This is for a spare input to be used with programmable outputs. |
25. | SPR4 – (RED L.E.D.) | This is for a spare input to be used with programmable outputs. |
26. | SPR5 – (RED L.E.D.) | This is for a spare input to be used with programmable outputs. |
27. | +24 – (RED L.E.D.) | This L.E.D. will indicate the board voltage that is protected by Fuse #2. |
28. | 24IN – (RED L.E.D.) | This L.E.D. will indicate 24 VAC to the board. |
29. | MCR+ - (RED L.E.D.) | This L.E.D. will indicate the status of the Control Voltage. If the Power On |
|
| button is pressed (Green Button Light is On), then the L.E.D. is ON. |
62
