Section, Cleaning | American Dryer Corp ADG-60 specification

SECTION I

ROUTINE MAINTENANCE

A. Cleaning

A program or schedule should be established for periodic inspection, cleaning, and removal of lint from various areas of the dryer, as well as, throughout the duct work system. The frequency of cleaning can best be determined from experience at each location. Maximum operating efficiency is dependent upon proper air circulation. The accumulation of lint can restrict this air flow. If the guidelines in this section are met, your new dryer will provide many years of efficient, trouble-free, and - most importantly - safe operation.

WARNING: LINT FROM MOST FABRICS IS HIGHLY COMBUSTIBLE. THE ACCUMULATION OF LINT CAN CREATE A POTENTIAL FIRE HAZARD.

WARNING: KEEP DRYER AREA CLEAR AND FREE FROM COMBUSTIBLE MATERIALS, GASOLINE, AND FLAMMABLE VAPORS AND LIQUIDS.

NOTE: SUGGESTED TIME INTERVALS SHOWN ARE FOR AVERAGE USAGE WHICH IS CONSIDERED SIX (6) TO EIGHT (8) OPERATIONAL RUNNING HOURS PER DAY.

DAILY (beginning of each work shift)

Clean lint from basket and tumbler.

Inspect lint screen and drawer for damage and replace it if torn.

WEEKLY

Clean lint accumulation from around microprocessor temperature sensor probes and sensor bracket assemblies.

90 DAYS

Remove lint from air vents and surrounding area.

IMPORTANT: Lint accumulation will restrict the air flow over the motor, causing overheating and irreparable motor damage. Motor failure due to lint accumulation will

VOID THE WARRANTY.

Remove lint accumulation from around the openings in the dryer's back panels.

Remove lint from gas valve burner train area with a dusting brush or vacuum cleaner attachment.

3

Image 7

American Dryer Corp ADG-60 service manual Section, Cleaning

Contents

VAC Phase Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Electrical Troubleshooting Section Cleaning Lubrication Adjustments To Remove Lint Drawer To remove gas valve train assemblyTo remove control middle or lint lower door To Remove Control Box To Remove and Replace Lint Drawer Switch AssemblyTo Remove Front Panel To Remove and Replace Sensor Bracket and Components To Remove or Replace Belt Loctite To Remove or Replace Motor Reverse steps 1 through Loctite To Remove or Replace Impellor Fan Belt and Idler Tension Adjustment To Replace Dual Control Microprocessor DMC Computer Fan Belt and Tension Adjustment To Replace Coin Acceptor To Replace Touchpad Keypad Basket Tumbler Alignment Vertical To Replace either Motor Relay Basket Tumbler Alignment Lateral To Replace Basket tumbler or Basket tumbler Support Loctite Important Never strike the shaft directly with a hammer To Replace Basket tumbler Support Pillow Block BearingPage To Replace Basket Tumbler Support Flange Bearing To Replace 330º F Burner Hi-Limit Switch Thermostat To Replace Main Door Switch To Replace Sail SwitchTo Replace Direct Spark Ignition DSI Module BB. To Replace Gas Valve AA. To Replace Ignitor and Probe DD. To Replace Coin Vault Discontinue power to the dryer HH. To Replace Main Door Hinge FF. To Install New Main Door GlassEE. To Remove Main Door GG. To Replace Main Door Gasket No L.E.D. Display Troubleshooting DMC computer L.E.D. display reads dSFL DMC computer L.E.D. display reads Sefl DMC computer L.E.D. display reads Hot If dryer is equipped with optional battery back up Condensation on main door glass Dryer operates, but is taking to long to dry Excessive noise or vibration Dryer is making scraping noise at basket tumbler area No Display Condition Electrical Troubleshooting No Start Condition Motor Doesnt Turn No Heat Condition Gas DOOr Condition DSFL Condition Data Label Technical Information HOW to USE a Manometer Using a Manometer Clcc E.D. Display Codes Fill Diagnostic L.E.D. Display Failure Codes Phase 5 System Diagnostics Phase 5 DMC Computer Relay Output L.E.D. Indicators E.D. Display Indicators DOT Phase 5 DMC Computer Input and Output L.E.D. Indicators WR ADC450162 1- 10/15/98-50