American Dryer Corp AD-25, SL31AD-15 Q. PROGRAM LOCATION 14 (PL14)

Q. PROGRAM LOCATION 14 (PL14)

Maximum Time for Auto Dry

Summary: The maximum auto dryness time is programmable from 1 to 99 minutes.

(Wait 3-Seconds)

(“Hold In” to Accelerate)(“Hold In” to Accelerate)

(Time Decrease) (Time Increase)

PL14

PERM PRESS

Adrt

PL15

LO TEMP HI TEMP

Contents

Main AD-15/AD-24/AD-25/AD-30/AD-285/AD-50 Installation Manual (Gas / Electric / Steam) Phase 3 Coin / Phase 4 Coin / Phase II Non-Coin Retain This Manual In A Safe Place For Future Reference Important Page Page Table of Contents Page Page SECTION I INTRODUCTION PHASE 3 FEATURES Page Page SECTION II INSTALLATION PROCEDURES A. INSTALLATION NOTE: Always keep the dryer in an upright position. B. LOCATION OF THE DRYER Page Page H. GAS DRYERS I. GAS FLAME ADJUSTMENT J. STEAM DRYERS (LOW-PRESSURE) K. STEAM DRYERS (HIGH-PRESSURE) L. BASKET (TUMBLER) M. GROUNDING SECTION III L.E.D. DISPLAY AND CODES SECTION IV OPERATING INSTRUCTIONS A. TIMED MODE B. AUTOMATIC MODE C. FREE DRY MODE SECTION V PROGRAM SELECTIONS NOTE: Programs are stored in the computer memory and are cataloged as program locations (PL). Temperature Display Mode Right Coin Count (rCC) Timed Mode (tInE) Antiwrinkle Program (Grd) Buzzer/Tone (bUZ) Free Dry Mode (FrEE) Coin Mode (Coin) Bad Coin Lockout Status (bCLO) Bad Coin Reset (bCrS) Accumulative Time (AtIn) Single Coin Dual Coin Accumulative Coin (ACOn) Single Coin Acceptor Dual Coin Acceptor Page Page Page SECTION VI INTRODUCTION TO PROGRAMMING Page SECTION VII PROGRAMMING A. TEMPERATURE DISPLAY MODE B. RIGHT COIN COUNT (rCC) C. LEFT COIN COUNT (LCC) D. PROGRAM LOCATION 01 (PL01) Page Page Page E. PROGRAM LOCATION 02 (PL02) F. PROGRAM LOCATION 03 (PL03) G. PROGRAM LOCATION 04 (PL04) H. PROGRAM LOCATION 05 (PL05) I. PROGRAM LOCATION 06 (PL06) J. PROGRAM LOCATION 07 (PL07) K. PROGRAM LOCATION 08 (PL08) L. PROGRAM LOCATION 09 (PL09) M. PROGRAM LOCATION 10 (PL10) N. PROGRAM LOCATION 11 (PL11) O. PROGRAM LOCATION 12 (PL12) P. PROGRAM LOCATION 13 (PL13) Q. PROGRAM LOCATION 14 (PL14) R. PROGRAM LOCATION 15 (PL15) S. PROGRAM LOCATION 16 (PL16) 47 SECTION VIII FACTORY PRESET PROGRAMS Dual Coin Sing le Co in Only SECTION IX NON-COIN COMPUTER DRYER Non-Coin Features Non-Coin Computer Dip Switch Features Operating Instructions - Non-Coin Computer Dryer A. COMPUTER DISPLAY CODES B. AUTOMATIC ONLY (NON-REVERSING DRYERS) C. AUTOMATIC/MANUAL PROGRAM SELECTABLE (AUTO SELECTED, NON-REVERSING DRYERS) D. AUTOMATIC/MANUAL PROGRAM SELECTABLE (MANUAL SELECTED, NON-REVERSING DRYERS) E. MICROPROCESSOR REVERSING DRYER Page SECTION X SERVICE/PARTS INFORMATION A. SERVICE B. PARTS SECTION XI REPLACEMENT PARTS LIST Additional Parts Available But Not Illustrated SECTION XII WARRANTY INFORMATION A. RETURNING WARRANTY CARDS B. WARRANTY C. RETURNING WARRANTY PARTS Page SECTION XIII ROUTINE MAINTENANCE A. CLEANING SUGGESTED CLEANING SCHEDULE B. ADJUSTMENTS C. LUBRICATION SECTION XIV TROUBLESHOOTING Page H. An excessive noise or vibration in the dryer... I. The dryer is cycling on the hi-limit switch... J. The impellor motor or the drive motor will not operate... K. The dryer does not start, display shows door... L. Display shows dSFL... M. Dryer does not respond to command at keyboard (touch pad)... N. Dryer motor starts, but gas valve and Globar DO NOT operate... O. Dryer motor starts, gas valves primary coil operates, but Globar does not heat up... P. Dryer motor starts, gas valve and Globar operate, but gas does not come on... SECTION XV OPTIONAL 9 VOLT BATTERY BACKUP