American Dynamics 8200-2646-02 B0 guide

Installation and Operation Guide

3.2IP camera SD card Troubleshooting

1.Check if the SD card position is correct or not. Please refer to the manual for the related information.

2.After powering the IP camera on, correctly insert the SD card, and a little icon of "SD" will show up in the upper-right corner of the monitor screen. If not, it means the device detection has failed. Please contact your technical support and ignore the following steps.

3.If no cross sign appears beside the "SD" icon, please go on to the next step. If a cross sign appears, please check the following:

a.Is it really an SD "Memory" Card?

b.Is this SD card formatted in the FAT16 format?

c.Connect the SD card with a PC and test to see whether the PC can read the data or not.

d.Does this SD card still have the capacity for storing data?

e.Is the SD card set to write?

If all the answers are "yes" but the cross sign still persists, please contact your technical support and ignore the following steps.

4.Please make sure the function of "SD CARD ENABLE" is activated in the ALARM and SCHEDULE pages if no cross sign appears beside the "SD" icon on the screen.

5.After recording, read the data on the web page of "sdget.htm". If the data cannot be read through the network, please read it instead in a PC, check the data stored in the "LANCAM" directory and contact your technical support regardless of whether there is data or not.

WARNING:

1.Performing this troubleshooting process may need a monitor, a PC, a card reader and some cables.

2.If the SD card is removed while storing or accessing data, the data will be lost.

3.If there is a cross sign beside the "SD" icon, it means the SD card has been inserted into the IP camera but cannot perform its writing function. Possible reasons are:

a.It is not an SD memory card.

b.The SD card is unformatted or formatted in a non-FAT16 or non-FAT12 format.

c.The file system is damaged.

d.The capacity of the SD card is full.

e.The SD card is set to be read only.

4.Turn off the power before inserting the SD card. Otherwise the unit may shut down.

19

Image 19

American Dynamics 8200-2646-02 B0 manual IP camera SD card Troubleshooting

Contents

Version1.6 Installation & Operation GuidePage Copyright Table Of Contents Icrosoft I Nternet E Xplorer Operation Instructions for the Network Safety Precautions Product Instructions Product Features Gpio Front ViewSD Card slot 5pin Mini USB Port Ethernet PoE Alarm wiring diagram Video OUT ConnectorPlug Inlet Dhcp on Dhcp OFF USB function Connect to a PoE HUB PoE Power over EthernetSummary Comparison of PoE Standards Compatible PoE HUB Manufacturer Pin1 & Pin2 short Pin2 & Pin3 short Power LED & IR LED Power setting Pin1 & Pin2 short J2 Jumper Controls ON/ OFF function of the IR LED 45∘ Lens adjustmentFocus adjustment II. Adjust the camera angle Cover Attaching Dome cover Dome body Ceiling mounting Installation UPDATE.BIN IP camera SD card Troubleshooting Enable Dhcp Function Network ConfigurationConfigure Your IP Camera Network Settings PC Wiring Configuration Set IP Address TCP/IP Communication Software TCP/IP Installation Select TCP/IP, and then click Properties TCP/IP configuration setting Click Start → Programs → MS-DOS Prompt Connection Testing Type Camera IP address Operation Instructions for the Network RJ-45 socket Microsoft Internet Explorer Connecting the IP camera Browsing images from the IP camera Homepage of Mjpeg mode Video setting page of Mjpeg mode Change Video Setting Installation and Operation Guide Mjpeg mode Viewer type Description of function keys MPEG4 modeDevice Title Resolution Fine Tune mode Change the Network Setting Http Port Default GatewayDescription of function keys IP Address Netmask User Name Change the Network Setting FTP Mjpeg mode onlyPassword Description of function keys FTP IP Address Email Address Change the Network Setting Smtp Mjpeg mode onlyDescription of function keys Account Name & Password Smtp Server Description of function keys Sntp Server Time Zone Submit Change the Network Setting Sntp Change the Network Setting Ddns Ddns Host Name Description of function keys Enable Ddns FunctionDdns Password Ddns Type Change the Network Setting PPPoE Upstream Internet gateways using UDP port Change the Network Setting -UPnP Change the Network Setting IP Filter Description of function keys Maximum Upload Bandwidth Change the Network Setting -Network Traffic Set Manually Change the System SettingSet the Date and Time of the system Description of function keys Local Time Timestamp Format Submit Change the System Setting Timestamp Change the System Setting Users Description of function keys Digital Input Digital Output Change the System Setting Digital I/O Description of function keys Change the System Setting Audio 255 Description of function keys Baud rateType Device ID Change the System Setting Update Firmware Description of function keys First Previous Next View the Event Logs Alarm Memory Buffer Change the Application SettingUpload Rates Recording Rate SD Card setting page of Mjpeg modeDescription of function keys Mjpeg Format Max Mjpeg Numbers Description of function keys File numbers Change the Application Setting -Language Setting Description of function keys Enable Record Upload Via FTP Record setting page of Mjpeg modeEnable Record Save Into SD Card Remove All Schedules Change the Application Setting -Record ScheduleChart Schedule Enable Alarm Upload Via Smtp Mjpeg modeEnable Alarm Upload Via FTP Enable Alarm Save Into SD card Motion Detection Description of function keys Targeted zoneDetection Range Save Change the SD card Setting PPPoE Settings PPPoE & Ddns Using the PPPoE Test Go to the Internet Ddns settings Bandwidth Calculator of the IP camera Question Tick on Enable ALARM-SAVE into SD Card to activate it Use IE to view the recorded files Set the recording time the AVI duration of the SD cardSet the PPPoE function Delete a user Use the Sub Hostname to view the IP cameraAdd a new user Modify the user Specifications Functions of client PC Check the IP class of your PC Appendix 1. -IP camera UPnP How To Installation and Operation Guide Installation and Operation Guide Install UPnP Packets Installation and Operation Guide Turn on Services Installation and Operation Guide Installation and Operation Guide Installation and Operation Guide Scan LANCams through My Network Place Appendix 2. -The ARP function Setting the IP AddressARP and ping from Windows or MS-DOS ARP and ping from Unix or GNU/Linux Appendix 3. -Register as a Ddns member Set up the DdnsRegistering for a Ddns Create an account Installation and Operation Guide Address. It will renew the IP Address automatically Installation and Operation Guide Unit is in Mbps/second Appendix 4. -MPEG4 Bit Rate Lookup Table of IP camera Provided accessories Appendix 5. -PoE Installation MethodAC Adapter Input AC 100-240V output DC Power Cord Indoor Mini-dome Power over Ethernet Injector Step Appendix 6. -FAQ