Installation
Instructions
TROPIC7038.401
Bidet Faucet and Vacuum Breaker with
EverClean™ Finish & SpeedConnect™ Drain
Congratulations on purchasing your American Standard faucet with EverClean finish and Speed Connect drain, two features found only on American Standard faucets.
EverClean Finish | Certified to comply with ANSI A112.18.1 | |
• One wipe effortlessly removes spots | SpeedConnect Drain* | M 9 6 8 8 9 4 |
• Eliminates the need for cleaners and scrubbing |
| |
• Permanent surface protectant remains beautiful | • Fewer parts, installs in less time | |
• Never needs adjustment | ||
for the life of the faucet | ||
• Guaranteed to seal properly the first time, every time. | ||
• EverClean™ available on: Polished Chrome, Satin Nickel, | ||
| ||
Stainless Steel, Polished Brass (or any combination of these finishes) | ||
*Your new American Standard faucet is designed to work only with the SpeedConnect drain. | ||
To ensure that your installation proceeds
|
|
| 8 TO 12 | |||
TRANSFER VALVE (FOR FLUSHING |
|
|
|
| ||
| RIM OR SPRAY) |
|
|
|
| |
BIDET OUTLINE |
|
|
| (C) | (H) | |
IS SYMBOLIC | 7/8 DIA. |
|
| |||
|
|
|
|
|
| |
DOUCHE SPRAY | ADJ. |
|
|
| ||
| TO | DIA. |
|
|
| |
|
|
|
|
| ||
|
|
|
|
| ||
DIA. |
|
|
|
|
| |
|
|
|
|
|
| |
|
| FINISHED | FINISHED |
|
| |
|
|
|
|
| ||
|
|
| FLOOR |
|
| |
|
|
| WALL |
|
| |
|
|
|
|
|
| |
|
|
|
| |||
DIVERTER AND
VACUUM BREAKER
ASSEMBLY
FOR GROUND JOINT CONNECTION OR 1/2 " O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
Required tools
Screwdriver | Plumbers' Putty or |
| Caulking |
Phillips Screwdriver |
|
| Channel Locks |
Adjustable Wrench
Tubing Cutter
1 |
|
| Turn off hot and cold water | |
BIDET FAUCET INSTALLATION | CAUTION | |||
supplies before beginning. | ||||
|
|
Place RUBBER RING (10) into DECK ADAPTER (4).
Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From under side of mounting surface, install VALVE BODY (3, 3a) through valve mounting holes. Threads of VALVE BODY (3, 3a) should extent at least 5/16 of a inch above 4 mounting surface top. Fig. A. Thread DECK ADAPTER (4) onto VALVE BODIES (3, 3a)10 until snug against internal stop. If necessary, adjust LOCKNUT (1).
11
6
7
BIDET
LEDGE
Tighten LOCKNUTS (1) with WRENCH (5) (supplied) |
|
|
|
|
|
|
|
|
|
|
|
|
|
to secure VALVE BODIES (3, 3a). |
| Fig. A. |
|
|
|
|
|
|
| ||||
Remove MOUNTING NUT (6), WASHER (7) and |
|
|
|
|
|
|
|
|
| ||||
|
| 5/16'' |
|
|
|
| |||||||
UPPER GASKET (8) from TRANSFER VALVE (9). |
|
|
| MIN. |
|
|
|
| |||||
Insert TRANSFER VALVE (9) into the center forward |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
hole of BIDET. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replace UPPER GASKET (8) and WASHER (7) . Position the side threaded outlet rearward and secure MOUNTING
NUT (6). Thread ESCUTCHEON (11) onto TRANSFER 3, 3a VALVE (9) until it seats against the BIDET LEDGE.
4
10
MOUNTING
SURFACE
2
21
5
| 3 | 3a |
|
| |
HOT |
| COLD |
8
9
2 SPRAY INSTALLATION
8 | 2 | 9 |
7 | PUTTY | 1 |
Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside of SPRAY BODY FLANGE (2) and secure with NUT (3).
6
3 
Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1). Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet NIPPLE (7) of the TRANSFER VALVE (8).
Thread SPRAY CAP (9) onto SPRAY BODY (1).
4 | 5 |
| |
| 4 |
1
