Asus XG-DLS manual

R XG-DLS

Dual Xeon® ATX Motherboard

USER’S MANUAL

Contents

Page USER'S NOTICE Product Name: ASUS XG-DLS ASUS XG-DLS Manual Revision: 1.03 E316 Marketing Technical Support CONTENTS I. INTRODUCTION II. FEATURES III. INSTALLATION IV. BIOS SOFTWARE Details of Standard CMOS Setup: Details of BIOS Features Setup Details of Chipset Features Setup Details of Power Management Setup Details of PNP and PCI Setup FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual is Organized Item Checklist Features Special Features: Enhanced ACPI: Anti-Boot Virus BIOS & PC-cillin Intelligent Features: Auto Fan Off: even in sleep mode and system noise ASUS XG-DLSMotherboard ASUS XG-DLSMotherboard Layout Jumpers Expansion Slots/Sockets Hardware Monitor Connectors Layout Contents Installation Steps 1. Jumpers 2.System Memory (DIMM) DIMM Memory Installation Procedures XG-DLS 168-PinDIMM Memory Sockets 3.3V Unbuffered System Memory 3.Central Processing Unit (CPU) Xeon Processor Installation Step 3: Install the Retention Mechanism Brace Bars Step 4: Install Cartridge Lifters Step 5: Install a 2nd Processor or Termination Module Step 6: Install Retention Mechanism Cap Step 7: Install Retention Mechanism Frame Removing the Xeon™ Processor External Thermal Sensor (optional) 4.Expansion Cards Expansion Card Installation Procedure: Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor Accelerated Graphics Port 5.External Connectors 3.Parallel Printer Connector (25-pinFemale) NOTE 4.Serial Port COM1 and COM2 Connectors (Two 9-pinMale) 5.RJ-45Connector (8-pinFemale) 7.Floppy Disk Drive Connector (34-1pinFLOPPY) 8.Activity LED (2-pinsHDLED) 9.Primary / Secondary IDE connectors (Two 40-1pinIDE) 10.Ultra-Fast (50-pin)/Ultra2 (68-pin)SCSI Connectors IMPORTANT SCSI Connection Examples 11.IrDA-Compliantinfrared module connector (5-pinIR) 12.SB-Link™Connector (6-1pin SBLINK) 13.Message LED Lead (2-pinMSG.LED) 14.SMI Suspend Switch Lead (2-pinSMI) 15.ATX Power Switch / Soft Power Switch (2-pinPWR) 16.Reset Switch Lead (2-pinRESET) 17.System Power LED (3-pinKEYLOCK) 20.Chassis Intrusion Sensor Lead (4-1pin CHASSIS) 21.Wake-On-LANConnector (3-pinWOLCON) IMPORTANT: WAKE On LAN Power Up Con- trol CPU Cooling Fan Connectors (Three This connector supports a 3-pin Positive , the black should be Power Connection Procedures Flash Memory Writer Utility 2. Update BIOS Including Boot Block and ESCD Flash Memory Writer IV. BIOS Managing and Updating Your Motherboard’s BIOS Upon First Use of the Computer System 2.Copy AFLASH.EXE to the just created boot disk Run AFLASH.EXE from this new disk and select option 1. Save Current BIOS to File 6. BIOS Setup Load Defaults Details of Standard CMOS Setup: Time (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59) Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup Auto detection of hard disks on bootup Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled Video (EGA/VGA) Details of BIOS Features Setup BIOS CPU Level 1 Cache / CPU Level 2 Cache (Enabled) CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache BIOS Update (Enabled) PS/2 Mouse Function Control (Auto) OS/2 Onboard Memory > 64M (Disabled) MPS 1.4 Support (Disabled) Leave on default setting for best performance PCI/VGA Palette Snoop (Disabled) Details of Chipset Features Setup Graphics Aperture Size (64MB) Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Memory Hole At 15M–16M(Disabled) Onboard FDC Swap A & B (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Details of Power Management Setup Video Off Method (DPMS OFF) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Disabled Wake On LAN (Enabled) Automatic Power Up (Disabled) Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) Onboard AHA BIOS (Auto) ONB AHA BIOS First (No) SCSI Channel B/A Term (Enabled) Load BIOS Defaults Load Setup Defaults Load Supervisor Password and User Password Forgot the password Passwords IDE HDD Auto Detection Save & Exit Setup Save & Exit Exit Without Saving