Example System | Audio Authority Car Audio System manual

	EXAMPLE SYSTEM 1 •		Addressing	•	Low-Level Bus
	TWO-CHANNEL SYSTEM	•	System Bus	•	Speaker Bus
	TWO-CHANNEL SYSTEM	•	DC Bus	•	Amplifier Bypass
		•	DC Bus	•	Amplifier Bypass

2/77 Power Source

Amplifiers	916X	942
		4/01

903

980

02 910

01 910

System Bus

Speaker Bus

LevelBus	AmplifierBypass
Low-

High Powered Sources

4/00R	RightFrontSpeakers	ADDRESSINGKEY	R4/01 (932only)	MODULEGROUPID
932			RIGHT
			LEFT-
SpeakerBus	SampleSystemCapacity:	8 Sources(2chlow&2chhigh-level) 3 FrontAmplifiers(2chinput&2choutput)	8 SpeakerPairs	ProcessorBypass AmplifierBypass

932	FrontSpeakers	ControlCable SystemBus SpeakerBus Low-LevelBus DCBus 4GaugeBlack 4GaugeRed
4/00L	Left

	ASD Tech Support USA and Canada: 800-322-8346(Mon-Fri 8:30 AM to 5:00 PM Eastern Time)
40	Phone: 859-233-4599 Fax: 859-233-4510 Hookup drawings and FAQ http://www.audioauthority.com

Image 40

Audio Authority Car Audio System Example System, Addressing Low-Level Bus, System Bus Speaker Bus DC Bus Amplifier Bypass

Contents

Demonstration Network Car Audio Page Contents Introduction What is the Access System? Definition of Terms Product Select HOW the Access System Works Selecting Products in the Access SystemBuses 922 Access System Components Access User InterfacesControl Panels Full-Featured Control Panel Features include Switching Modules Expander Modules System ModuleSystem Specific Components DC Distribution Modules Choosing the Correct Switching Modules Product GroupsHead Units 910 Amplifier Product Groups Amp Sharing Ampifier Bypass Speakers Begin Installation Address and Other SettingsPreparation Number the Product Groups Determine the Module ID settings How to Use These TablesSources, EQs and Amplifiers Speakers Set the Programming Switches Set the Address SwitchesProgramming Switch Settings S M B T D Set the Left-Right Switch Timeout Minutes and ModelSilenTouch and Model Speaker Limit Installing the System Hardware Designate the Switching Module LocationsDetermine Other Module Locations Mount the Modules Blue Install Speaker Bus Low-Level Buses EQ and Amplifier Bypass Low-Level Bus Illustration.Low-Level Install the DC Power Distribution Cables Choosing the Power Mode for Your Display Power Supply Ventilation Setting the Parallel Speaker Limits Install the RF Antenna Distribution System Check Your Work to This Point Observe correct polarity for all bus connections Installing a Control Panel Rear view of the 902 Control Panel Control Panel Expanders Control Panel Cutout Sizes Installing Product Select Buttons and Product Indicators Be careful to maintain PSB Cable polarity at both ends Remote Power Switch System Module AccessoriesTheftAlert Remote System Reset Testing Network Function902 Page Install the First Products Display Component HookupPage Test Your Initial Product Installation Connect the Battery Install the Remaining ProductsTroubleshooting Noise Problems Test Product Selection Selecting Additional Speaker Pairs with PSBs Deselecting Products with PSBsB System Comparison TheftAlert Protection System, DC and Signal Bus Wiring Diagrams Product to Switch Module Wiring Diagrams Addressing Low-Level Bus Example SystemSystem Bus Speaker Bus DC Bus Amplifier Bypass System Bus Addressing Amp Bypass EQ Bypass AMP Shared System 942 916X 932 Example of split Model 910D Setup Ch. High-Level 2-Ch Low-Level Head Unit Channel Signal Processor Or Equalizer Power Expander915X DC EQ Bypass Note Channel Setup for 980EZ Model 980 System Module / 2- and 6-Channel Hookup Amplifiers / 2-Channel Hookup Channel Amplifier916X Amp Bypass Note Amplifiers / 4-Channel Hookup BAT+ Shared Amplifier Hookup 942 Left/Right and Mono Speaker Hookup Left Speaker Right Access Warranty Limited WarrantyWarranty Service Procedures Out of Warranty Service Index