|
| Time setting for valve from |
|
|
|
| Display and adjust output value | ||
| full close |
| to full open. (Display when |
|
|
|
| of 1st output group | |
| valve control is ON) | (Display in PID control mode and manual | |||||||
|
| RUN mode) | |||||||
Press |
| ||||||||
| Press |
|
| ||||||
|
|
|
|
|
|
| |||
|
| Valve Dead Band setting. |
|
|
|
| Display and adjust output value | ||
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| of 2nd output group | |
(Display when valve control is ON) |
|
|
|
| |||||
(Display in dual loop PID control mode and | |||||||||
Press | |||||||||
| manual RUN mode) | ||||||||
|
|
|
|
| Press |
|
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| In case of using an external CT, | |||
|
|
|
|
|
| ||||
|
|
|
|
|
| the controller displays the current | |||
| valve output with feedback to |
|
|
| |||||
|
|
|
| value being measured by CT, if | |||||
| controller. (Display when valve |
|
|
| the control output is ON | ||||
| signal feedback function is ON) | Press |
| to return to set target temperature | |||||
Press |
| ||||||||
|
|
|
|
| |||||
|
|
|
|
|
|
| Valve output with feedback. | ||
|
|
|
|
|
|
| |||
| valve output with feedback to | (Display | when valve feedback | ||||||
| controller. (Display when valve | function is ON) | |||||||
| signal feedback function is ON) | Press |
|
| |||||
Press |
|
|
|
|
| ||||
|
|
| Regulate temperature |
|
|
| DA value feedback of valve. | ||
|
|
|
|
|
| ||||
|
|
| deviation value | (Display | when valve feedback | ||||
| Press | function is ON) | |||||||
| Press |
| Back to target temperature | ||||||
|
|
|
|
| |||||
Regulate
output value
(The setting display when analog output) Press 
Regulate
output value
(The setting display when analog output)
Press 
to return to
* 1 Scale = 2.8uA = 1.3mV for tuning output value
ASCII, RTU communication format selection
Press
Communication address setting
Press
Communication baud rate setting
Press
Data length setting Press 
Parity bit setting
Press
Stop bit setting
Press 
to return input type setting
PID mode selection: any one of 4 groups PID modes (n=0~3) can be selected. When n=4, program will automatically select 1 group PID that is most useful for target temperature.
| Select n=0~4 to | PID setting: n=0.Press |
| PID setting: n=3.Press | |
| decide PID mode. |
|
|
|
|
Press | 0~3 groups PID |
|
|
|
|
|
| Proportion band setting: n=0. |
| Proportion band setting: n=3. | |
|
|
| Press |
| Press |
|
| Ti setting: n=0. Press |
| Ti setting: n=3. Press | |
|
| Td setting: n=0.Press |
| Td setting: n=3.Press | |
|
| Integral deviation setting: n=0. |
| Integral deviation setting: n=3. | |
|
| AT setting. |
|
| AT setting. |
| Press | back to PID deviation setting | Press | back to PID deviation setting | |
Pattern and step editing selection: edit | in | parameter. The following display is the example operation of pattern No. 0. | |||
|
| Select desired editing pattern |
| Edit temperature of step No. 0 |
|
| Select actual step No. when | |||||||
|
| number |
|
|
|
| of pattern No. 0 |
|
| program control is executing | ||||
|
|
|
|
|
|
|
| |||||||
|
| select OFF | Press | Press |
| |||||||||
Press | select number |
| ||||||||||||
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
| |||||||
| Exit pattern and step editing selection |
| Edit time of step No. 0 of |
|
| Set additional execution cycle | ||||||||
Switch to |
|
| and continue setting |
| pattern No. 0, unit is hh.mm |
|
| number(0 to 99) | ||||||
|
|
|
|
| ||||||||||
|
| Press | Press |
| ||||||||||
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
| Set step No. 07 in order |
|
|
| Set link pattern, OFF indicates | |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| the program end |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| Edit temperature of step No. 7 |
|
| |||
|
|
|
|
|
|
|
|
| Press | to return pattern No. editing | ||||
|
|
|
|
|
|
|
|
| of pattern No. 0 | |||||
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
| Press | mode |
| |||||
|
|
|
|
|
|
|
|
|
| |||||
Edit time of step No. 7 of pattern No. 0, unit is hh.mm
Press 
to set actual step No.
4
