Manuals / Barco / Computer Equipment / Projector Accessories

Barco R9840170, R9840171, R9840176 manual Configuration Setup Lamp Read Mode

Models: R9840171 R9840176 R9840170

1 37

Download 37 pages 27.23 Kb

Page 19

Image 19

Configuration Setup

Lamp Read Mode

Reading the Lamp

The Lamp Read Mode requires a connection between the lamp unit and the Remote Control using the supplied lamp cable (Z34980143).

Reading the lamp is only possible for BARCO ELM and SLM projectors.

How to Connect

1.Plug the cable in the remote control connector labeled CTRL4 "Lamp Info Module".

2.Plug the other extremity in the Lamp Unit connector.

WARNING

To avoid burns always let cool down the lamp before handling it .

Page 19

Image 19

Barco R9840170 manual Configuration Setup Lamp Read Mode, To avoid burns always let cool down the lamp before handling it

Contents

R9840170 R9840171 R9840176 Rugged Remote Control for ELM/SLM ProjectorsBARCO PROJECTION SYSTEMS Tel +32/56/368211 Fax +32/56/351651 E-mail sales.bps@barco.com Produced by BARCO NV, October All rights reservedTrademarks are the rights of their respective owners BARCO n.v./Projection Systems Noordlaan B-8520 Kuurne BelgiumContents ContentsMechanical Info Rugged Remote Control Safety InstructionsInstallation Instructions Safety InstructionsSafety Instructions Notice on Safety1. This product should be operated from an AC power source Safety Instructions FEDERAL COMMUNICATION COMMISSION FCC STATEMENTSafety Warning On SafetySafety indication on the product Safety Instructions3. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord On installationOn repacking Safety InstructionsRefer all servicing to qualified service personnel On cleaningAccessories General InformationRugged Remote Control Upgrade KitsContents ContentsContents of the Rugged Remote Control Case Weight SpecificationsDescription Description & SpecificationsSerial interface RS 232/422 Description & Specififcations ChargerP US H Keypad Function when not specified idem RCUCommand Keys Description & SpecififcationsTermination resistor = 120 Ohms LED D when lit power present A B C D Description & Specififcations Wireless BaseWeight 0.3 kg 0.6 lbs Communication port A Serial interface C Selectable modes with switch B RS 422 T RS422 terminated1. Australia 2. US/Japan 3. Europe 4. UK Installation setupInstallation Setup Power ConnectionsSupplying the Wireless Base Installation Setup Power ON switchA image Installation Setup Charging the batteries POWER SAVE MODENO COMMUNICATION ADDR=1 BAT=LOW PRESS ADJUST TO ENTER NO UPDATERisk of explosion if the batteries are replaced by an incorrect type Installation Setup Changing the batteriesDispose of used batteries according to the instructions Configuration Setup Configuration SetupRemote Mode To avoid burns always let cool down the lamp before handling it Configuration Setup Lamp Read ModeASLQ*1DVVDGDSWHU*1$ Configuration Setup RS232/422 CommunicationSoftware download Configuration SetupRF Mode Configuration SetupHow to connect RF address Configuration SetupRemark concerning display images Menu SetupBAT=LOW/RF=LOW Menu SetupInstallation Settings Menu SetupRemark All the menus are of the closed loop type Identification menu Menu SetupBAUDRATE Menu SetupFlowchart COMMUNICATION MENU COMM.PORT AUTONO COMMUNICATION COMMUNICATION BAUDRATE Menu Setupwhen in the Communication Menu NO COMMUNICATION COMMUNICATION COM.PORT AUTORF Options 3257 200325756RF Options Synchronize base in Installation settings menu ADDRESS1Menu Setup How to change the address1. Press ADJ to enter the Internal Menu menu Menu Setup Lamp Mode Menu3. Select OPERATION MODE by pressing ENTER menu LAMP READ MODESLM G5 PERFORMER STANDBY Additionnal Information Additionnal InformationMessages Dimensions Mechanical InformationMechanical Information Mechanical Information Mechanical InformationNoordlaan 5 B-8520 Kuurne Belgium Printed in Belgium BARCO NV / Projection Systems