Connecting an S-Video source device | BenQ cp270 manual

Connecting an S-Video source device

Examine your Video source device to determine if it has an unused S-Video output socket available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video source device:

1.Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

2.Connect the other end of the S-Video cable to the S-VIDEOsocket on the projector. The final connection path should be like that shown in the following diagram:

AV device

S-Video cable

• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

•If you have already made a Component Video connection between the projector and this S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 18 for details.

20 Connection

Image 20

BenQ cp270 user manual Connecting an S-Video source device, To connect the projector to an S-Video source device

Contents

Welcome CP270 Digital Projector Table of contents Important safety instructions Refer servicing to qualified service personnelFuture reference Projector lamp is on Do not look straight at the projector Safety Instructions Do not block the ventilation holes This Apparatus Must be Earthed Introduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper side Controls and functions Projector Remote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Set Rear Table in the System Setup Basic Projector Positioning your projectorChoosing a location Front Table Obtaining a preferred projected image size Page Projection dimensions Connecting a computer ConnectionTo connect the projector to a notebook or desktop computer Connection Connecting Video source devices Best video qualityBetter video quality Least video quality AV device Component Video to VGA D-Sub adaptor cable Connecting a Component Video source deviceTo connect the projector to a Component Video source device AV device Video cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Connecting a composite Video source device To connect the projector to a composite Video source device Operation OperationStarting up the projector Using the menus Use / to highlight the System Setup Basic menu Utilizing the password function Setting a passwordIf you forget the password Security Settings Entering the password recall procedure Changing the passwordDisabling the password function Enter a new password Adjusting the projection angle Switching input signalAdjusting the projected image Auto-adjusting the image Fine-tuning the image size and clarity At the bottom of the image Magnifying and searching for detailsCorrecting keystone Use of the screen without altering the images aspect Ratio Selecting the aspect ratioAbout the aspect ratio Selecting a picture mode Picture modes for different types of signalsPC input signals D-Sub / Comp. analog RGB Video input signals S-Video, Video, D-Sub / Comp. YPbPr Using Wall Color Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Adjusting Brightness Adjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant Color Press Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-Right To cancel the timer, perform the following steps How to use the Timer On key?Or go to the System Setup Basic Panel Hiding the image Utilizing FAQ function Freezing the imageInformation menu Based on the information you want to know Press Mode/Enter To activate the High Altitude Mode System Setup Advanced menu isTo highlight High Altitude Mode Operating in a high altitude environment Shutting down the projector Main menu Sub-menu Options Menu operationMenu system Lamp mode Normal/Economic Lamp SettingsBasic Advanced Description of each menu Picture menu Source 4. System Setup Basic menumenu Color TemperatureSave Settings Timer Blank Timer Sleep TimerSettings Panel Key Reset All FAQ-Image InstallationFeatures Service Information menu Maintenance Care of the projector Setting Lamp mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hour Timing of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampPage Resetting the lamp timer Setup Advanced Lamp Settings menuDisplays. Press to highlight Reset lamp Tighten the screws that secure the lamp Cover Indicators Troubleshooting Specifications Projector specifications Dimensions Timing chartResolution Mode Supported timing for PC input Signal Format Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Horizontal Warranty and Copyright information Limited warrantyCopyright Disclaimer Regulation statements FCC statementEEC statement Weee directive