This Apparatus Must be Earthed | BenQ cp270 instruction

Safety Instructions (Continued)

17.Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury.

18.Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's wall socket and call BenQ to have the projector serviced.

Warning

•THIS APPARATUS MUST BE EARTHED.

•When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.

6 Important safety instructions

Page 6

Image 6

BenQ cp270 user manual This Apparatus Must be Earthed

Contents

Welcome CP270 Digital Projector Table of contents Future reference Projector lamp is on Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projector Safety Instructions Do not block the ventilation holes This Apparatus Must be Earthed Projector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Controls and functions Projector Remote control Remote control effective range Replacing the remote control batteryPull out the battery holder Choosing a location Set Rear Table in the System Setup Basic ProjectorPositioning your projector Front Table Obtaining a preferred projected image size Page Projection dimensions To connect the projector to a notebook or desktop computer Connecting a computerConnection Connection Better video quality Connecting Video source devicesBest video quality Least video quality Connecting a Component Video source device To connect the projector to a Component Video source deviceAV device Component Video to VGA D-Sub adaptor cable Connecting an S-Video source device To connect the projector to an S-Video source deviceAV device Video cable Connecting a composite Video source device To connect the projector to a composite Video source device Operation Starting up the projectorOperation Using the menus Use / to highlight the System Setup Basic menu If you forget the password Utilizing the password functionSetting a password Security Settings Disabling the password function Entering the password recall procedureChanging the password Enter a new password Switching input signal Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Fine-tuning the image size and clarity Magnifying and searching for details Correcting keystoneAt the bottom of the image Selecting the aspect ratio About the aspect ratioUse of the screen without altering the images aspect Ratio PC input signals D-Sub / Comp. analog RGB Selecting a picture modePicture modes for different types of signals Video input signals S-Video, Video, D-Sub / Comp. YPbPr Setting the User 1/User 2 mode Using Wall ColorFine-tuning the image quality in user modes Adjusting Brightness Adjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant Color Press Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-Right Or go to the System Setup Basic Panel To cancel the timer, perform the following stepsHow to use the Timer On key? Hiding the image Information menu Utilizing FAQ functionFreezing the image Based on the information you want to know Press Mode/Enter To highlight High Altitude Mode To activate the High Altitude ModeSystem Setup Advanced menu is Operating in a high altitude environment Shutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Lamp mode Normal/EconomicLamp Settings Advanced Description of each menu Save Settings Picture menu Source 4. System Setup Basic menumenuColor Temperature Timer Settings Blank TimerSleep Timer Panel Key Features Service Reset AllFAQ-Image Installation Information menu Maintenance Care of the projector Lamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampPage Displays. Press to highlight Reset lamp Resetting the lamp timerSetup Advanced Lamp Settings menu Tighten the screws that secure the lamp Cover Indicators Troubleshooting Specifications Projector specifications Resolution Mode DimensionsTiming chart Supported timing for PC input Supported timing for Video and S-Video inputs Signal FormatSupported timing for Component-YPbPrinput Horizontal Copyright Warranty and Copyright informationLimited warranty Disclaimer EEC statement Regulation statementsFCC statement Weee directive